Repairs and Technical

11,663 topics in this forum

1. Hartke HA3500 problems!

   By DawnPatrol1990, April 10, 2016
   • 10 replies
   • 8.5k views
   • 
   • BassHertz
   • July 22, 2016

2. Bass setup in Bournemouth

   By thebassist, July 19, 2016
   • 2 replies
   • 687 views
   • 
   • Number6
   • July 21, 2016

3. Neck finish improvement

   By martthebass, July 20, 2016
   • 3 replies
   • 805 views
   • 
   • martthebass
   • July 20, 2016

4. 2 pack lacquer - powdery film/bloom on older re-finished bass?

   By three, July 17, 2016
   • 2 replies
   • 869 views
   • 
   • three
   • July 19, 2016

5. Warwick just-a-nut III

   By Trueno, July 14, 2016
   • 14 replies
   • 2.3k views
   • 
   • Andyjr1515
   • July 19, 2016

6. Fender strap locks keep coming loose

   By Andytre, July 3, 2016
   • 6 replies
   • 2.4k views
   • 
   • Bassmonkey
   • July 18, 2016

7. Truss Rod Rattle

   By tess, July 15, 2016
   • 9 replies
   • 1k views
   • 
   • tess
   • July 16, 2016

8. Removing a rusted saddle grub screw

   By umcoo, July 4, 2016
   • 10 replies
   • 1.8k views
   • 
   • umcoo
   • July 16, 2016

9. Tru-oil and slurry technique with stains

   By Andyjr1515, July 13, 2016
   • 11 replies
   • 6.1k views
   • 
   • Andyjr1515
   • July 15, 2016

10. Tuner ferrule size on Squier Affinity basses?

    By Mylkinut, July 14, 2016
    • 1 reply
    • 1.1k views
    • 
    • Mylkinut
    • July 15, 2016

11. Fender '62 / '63 Precision Pickup Pole Pieces

    By chrisaxe, July 9, 2016
    • 2 replies
    • 2k views
    • 
    • chrisaxe
    • July 14, 2016

12. "Zero" fret setup!

    By steviebee74, July 11, 2016
    • 7 replies
    • 1.8k views
    • 
    • rmorris
    • July 13, 2016

13. Converting 8 ohm cab to 4 ohm through new speakers

    By chrisaxe, July 7, 2016
    • 10 replies
    • 1.3k views
    • 
    • Phil Starr
    • July 12, 2016

14. Help Needed - someone good with circuitry/soldering?

    By Painy, June 21, 2016
    • 8 replies
    • 1.2k views
    • 
    • Painy
    • July 11, 2016

15. 3D Printing pickup covers / handmade pickup covers

    By Dood, June 28, 2016
    • 6 replies
    • 1.1k views
    • 
    • JonesTheCat
    • July 11, 2016

16. Pickup wiring question

    By hooky_lowdown, July 11, 2016
    • 4 replies
    • 802 views
    • 
    • Grangur
    • July 11, 2016

17. Carlsbro Delta Bass

    By cd_david, July 11, 2016
    • 0 replies
    • 687 views
    • 
    • cd_david
    • July 11, 2016

18. Need Some Help Finding a P Pickup

    By BruceBass3901, June 28, 2016
    • 16 replies
    • 1.9k views
    • 
    • tom1946
    • July 11, 2016

19. Hartke LH 500 fault (Volume decreases)

    By Mog, July 6, 2016
    • 5 replies
    • 2.2k views
    • 
    • Mog
    • July 11, 2016

20. Eden WTX 260 - rubber feet and screws??

    By dodgnofski, July 5, 2016
    • 3 replies
    • 829 views
    • 
    • JapanAxe
    • July 10, 2016

21. Ampeg B100R speaker blown?

    By Westenra, July 9, 2016
    • 0 replies
    • 587 views
    • 
    • gjones
    • July 9, 2016

22. Snapped Trussrod - Spector NS2B - Through neck!!!

    By grunge666, July 7, 2016
    • 13 replies
    • 2.8k views
    • 
    • Kev
    • July 8, 2016

23. anybody recognise this volume pot?

    By PaulWarning, July 8, 2016
    • 1 reply
    • 851 views
    • 
    • PaulWarning
    • July 8, 2016

24. Pickup pole pop

    By happyripper, July 4, 2016
    • 5 replies
    • 1k views
    • 
    • mcnach
    • July 7, 2016

25. Bad pre amp tubes?

    By DawnPatrol1990, July 4, 2016
    • 1 reply
    • 682 views
    • 
    • Dan Dare
    • July 7, 2016