Jump to content
Why become a member? ×

Struggling th500


danbanbass
 Share

Recommended Posts

Hi guys, I'm struggling to get a good sound with this head. I play in a Foo fighters tribute band and can't get it to sound right. I've played with eq etc but feels growly and loose.

Any hints or ideas.....kinda feeling like I should've bought an Ampeg :-/

Link to comment
Share on other sites

To get a more Ampeggy type sound from the TH, turn the Drive all the way up, then set the Gain to how much overdrive/gain required/not required, then get your overall volume form the Master Volume. Doing this tightens up the low end, although you do lose some highs as well. As such it does make the sound more middy, so again, drop (or boost if wanted) the mids.

I have a driven sound if hit hard, and also use a P-bass, I have Drive on Full, Gain at Midday, Bass at Midday, Treble at 2 o`clock, and both Mid Freq and Mid Level at 10 o`clock. Reduce the Gain to stop the growl, and then be in traditional Ampeg territory. Also bear in mind that the Quarterpounder pickup in the Nate is very powerful, so you`ll probably need to really reduce Gain and up Master Volume.

Link to comment
Share on other sites

Have you tried adding a compressor? An always on comp with very light settings will help to control and tighten your sound up. Alternatively try a different bass with similar settings, and try to isolate the issue.

The TH's are FANTASTIC amps, but they require some learning/playing with to understand just how to get the tone you want.

Link to comment
Share on other sites

The Gain and Drive controls on the Tonehammers take some getting used. The drive, for example, doesn't just create a distorted type sound, it also interacts with the EQ section and basically changes your EQ.

I'd never describe it as either growly or loose. Try it with a Jazz bass. Mine sounds very tight

It takes some getting used to.

That said, if you want a Foo Fighters sound, buy Ashdown

Edited by Marvin
Link to comment
Share on other sites

[quote name='Marvin' timestamp='1461489967' post='3034987']
The Gain and Drive controls on the Tonehammers take some getting used. The drive, for example, doesn't just create a distorted type sound, it also interacts with the EQ section and basically changes your EQ.

I'd never describe it as either growly or loose. Try it with a Jazz bass. Mine sounds very tight

It takes some getting used to.

That said, if you want a Foo Fighters sound, buy Ashdown
[/quote]

All good points, and the last one pretty spot on. The Rootmaster head gets the classic Ashdown sound, and is only a tiny bit bigger than the TH500. Heard one last week and was very impressed with it.

Link to comment
Share on other sites

[quote name='chris_b' timestamp='1461494907' post='3035073']...get an amp that makes a great sound and lets you sound like you, not someone else.
[/quote]

But the fellow said, in his original post ...

[quote name='danbanbass' timestamp='1461364132' post='3034146']...I play in a Foo fighters tribute band and can't get it to sound right....
[/quote]

... so is obviously trying to sound like the Foo Fighter's bassist. Just sayin'. :mellow:

Edited by Dad3353
Link to comment
Share on other sites

[quote name='danbanbass' timestamp='1461364132' post='3034146']
I'm struggling to get a good sound with this head. I play in a Foo fighters tribute band and can't get it to sound right.
[/quote]

If you're trying to sound like Nate then you should probably buy an Ashdown rig.

[quote name='Marvin' timestamp='1461489967' post='3034987']
...if you want a Foo Fighters sound, buy Ashdown
[/quote]

Whoops, beaten to it. A while back. ;)

Edited by discreet
Link to comment
Share on other sites

As sounds go... should be easy to achieve.
I think the TE were never that great way back then..depending on its vintage and miles on the clock too..
so that sounds a week link in the chain, for a start.

But if the OP has ruled that out..??

Link to comment
Share on other sites

I think I'm either just having trouble coaxing a tight clear useable sound from it, I've had Ashdown gear before and have never been blown away by it.

Nates clean bass sound is what I'm after in that vid, but Ashdown don't seem to compliment my playing, the other issue is I either can get the cut and loose the largeness in the sound or the opposite which looses the cut.

Part of me wonders if I should've got an svt 3 pro....

Link to comment
Share on other sites

[quote name='danbanbass' timestamp='1461523725' post='3035420']
I've had Ashdown gear before and have never been blown away by it.
[/quote]

Was that all-valve Ashdown like Nate's using? I think it's the all-valve bit that's important, doesn't necessarily have to be Ashdown.

Link to comment
Share on other sites

For the clean sound that Nate has on that clip Try the settings I put down earlier, but with Mid Freq at about 2 o`clock, and then adjust the Gain to however much breakup is required - probably 10 o`clockish. That gives the classic Ampeggy SVT type sound (got this from a thread on Talkbass). Too many mids for me, but it does that sound Nate has really nicely like that.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

 Share

  • Recently Browsing   0 members

    • No registered users viewing this page.
×
×
  • Create New...