itu

First and foremost, the sound is small. If you want some loudness, use an amp or buy a double bass. Don't be afraid of the fixed bridge, especially if you go fretless. Intonation is not an issue at all. Action can be tweaked with a file. Piezo reads any string that vibrates. Tuning the instrument so that the piezo/bridge parts work well may take few minutes. I have to say that I hated my instrument, a Kramer Ferrington. Sharp corners (think about your right hand on top of that bulky box), very quiet... I even tried piccolo strings on it and then it sang a bit. But the loudness (the lack of it) was the main reason to sell it. There was nothing I couldn't do with an electric bass. Some have said that it is good at home while practicing. Not me, no more.

Ordered it. Let''s see, what it is. Bought it via Reverb.

Have to say, that I love your work. The idea of having a fully parametric EQ in the preamp section is top! Many times I have had issues with different places: some frequency is dead or even worse, the other way around. On the other hand P-EQ gives many possibilities to tweak the sound of the bass. My Glockenklang Soul has very functional EQ - but it lacks parametric. I have a cheap para by Artec and it can save the place related issues. Quality it is not but can be a temporary help in need.

OK, to clarify things a bit before someone wants to put words to my mouth: It is fine to get THAT sound from any preamp or signal route someone happens to love. Me, I am after components that can offer transparent sound. I am not totally satisfied with my MG's bartolini pre, although the pickups I do like. I changed the hi-Z parts (vol & blend) to their active counterparts and the sound changed. Even the NTMB behaves better now. My wish would be an adjustable LPF, a parametric, and a tilt EQ. In this order. My Vigier Passions (series II) have a treble and a semi-parametric that I like. I could change that treble to an Alembic type filter circuitry. But before them I want buffered pickup outputs. It means that then lo-Z vol or blend or tone do not affect each other.

...only has active tone. It does not have a completely lo-Z signal route. Just tone. And that is actually the hi-Z part of the preamp. Plain blend (and vol) pot. I was after that Noll to get a lo-Z blend. Now I have it. It is different.

Is your signal route active from the blend to tone or just tone? I am interested in the buffered mixing to prevent load issues with the pickups. Passive carbon pots are something I downright hate. I built few step attenuators with metal film resistors. I tried few different alternatives of how many dBs one step is and the total resistance. Simple maths. Now I have a Noll Mixpot before a bartolini NTMB in my Modulus Graphite. Sound got an upgrade.

If you use a hi-Z (passive) bass, I would try compressor or od/dist/fuzz right after the bass and move the tuner further away in the signal chain. Tuner may have a lo-Z output and its output may sound very different with those effects mentioned. So try these alternatives before attaching the units to your board. I want to drive my effects with my bass before putting the signal to compressor IF the compressor's sound does not change too much, if it is later in the chain. This is so much trial and error - there are no absolute truths here.

This is very good point. If that bass preamp can give as good a performance as that amplifier's preamp, fine. Think about Anthony Jackson's choice in his Foderas: a pickup, a wire and a Neutrik output jack. No preamp, no lousy pots. Maybe those mixing desks have somewhat better performance... @Passinwind: Please tell me about your setup in greater detail.

Do agree. I did not mean, that they do not exist at all.

I feel that Britons have more edge (not that Edge!) in their music. Americans tend to be a bit too happy and politically correct. They just can not say that they feel bad in minor. As was said earlier, Motown is top as there are also other acts that can not be beaten but overall I like Sex Pistols over Mariah Carey.

I suggest you grease that truss rod threads well when it arrives. It is very easy to do it before it goes inside that neck. Put some thicker good quality grease there and it will work for decades. At least the one I bought needed some greasing to work flawlessly.

I use the term lo-Z (low impedance) rather than active as it tells more about the important instrument output than "active" or "passive". Output, because it is the one seen by effects and amplifier inputs. NOTE: The hi-Z output of the passive bass may behave differently (than a lo-Z) with certain effects (especially od/dist/fuzz and compressor) or amplifier's preamp. That sound may be hard or downright impossible to achieve with lo-Z output. Because the output of any effect is lo-Z, bass output can affect only the first unit after that instrument. Bass signal route is usually like this: pickups - blend - vol - tone - output Blend - vol may be vol - vol but does not change the principle. If any part of the system is active the system output is low impedance (lo-Z). If you have an EMG fully active system (BTS + active pickups) the signal route is lo-Z all the way. Usually this is not the case. Very often the "active bass" has only active tone sculpting electronics. Good side is that these modules are easy to bypass or replace. Bad is that the (cheap) hi-Z blend and volume pots affect the sound of pickups (except in the case of lo-Z EMGs). If you want to buy a preamp, an Artec costs around £20 and has practically the same parts in it as that £200 Aguiklangowsky. If you want to get lo-Z blend and tone to your hi-Z pickups, you need to buy something else (East) or put a puzzle together by yourself. My choice was to include Noll's Mixpot (around £50) before a bartolini tone. Now the bass sounds different, yes. This setup was (relatively) cheap to me as the NTMB was already in the bass. Bad side was that I lost the A/P switch for the NTMB. It is of no use, as the Mixpot needs battery, too. (It might be feasible to have a simple override switch for all electronics, and be able to use the neck pickup in case of dead battery. Maybe.) East is the most flexible system that I know at the moment, as it has both hi-Z and lo-Z signal routes. It is also cheaper than the active-only-Sadowsky tone, so I think it is the alternative to who ever thinks about high quality hi-Z and lo-Z system in one well designed set.

You should check specs. Find the max SPL if it is available. If it is not, find the sensitivity. You can calculate max SPL via sensitivity and max wattage. If these numbers are not available, you can only trust your ears.

If you put the elements (each 16 ohm) in parallel, the total impedance is 8 ohms. If you connect them in series, you get 32 ohms.

Once more: If you compare the power between 8 and 4 ohm load, there is difference, yes. Some amp may give 200 W to 8 ohms and even 400 W to 4 ohms but maybe only 500 W to 2 ohms. As the load becomes harder to the amp, the ability (or the lack of it) to drive that load may affect the amp's maximum output. Bigger number equals easier load to the amp. Naturally it is not wise to exceed specifications to any direction. If you compare sound level between 8 and 4 ohm loads, there is practically no difference. You probably can not hear that. Amp's wattage has very little to do with loudness. Max SPL talks another language and that is directly related to the cab. It is not intelligent to compare loudness and wattage within a system when parts are separated. You need to take all parts to that equation. If you do not know the max SPL of the cab and its other specs, it is no reason to try to approximate the maximum loudness of the system through a simple number from the amp.

The most important thing is that it is attached well. So if you make a change, tighten the screws (to body) after a month or so. I think that there are few different designs: some attach bridge pieces together with screws so they do not move anywhere, while some have these F-type saddles that may move under some serious funkin'. I have had that issue with one Wilkinson bridge. Took some time to find the reason for funny rattle.

It may be so that the FX loop (send/return) is corroded, so put a short cable there to connect pre and power amps. If the vol needs to go beyond 12 o'clock, there is not too much power in the amp OR the gain is too low. Every EQ (B, T, M, shape etc.) is actually part of the gain circuitry. If you boost with EQ, you should lessen the gain. Soundwise it is usually more effective to cut with EQ and boost with gain. Make trial without any effects: put the amp vol to around 10 o'clock. Set your EQ. Add gain until you get audible distortion. Back up that gain just a bit to remove it. This is the gain level you should use. Do not care about the level meter reading, trust your ears. Usually those meters should reach that red area from time to time with reasonable, undistorted levels.

Tilt EQ is similar to Quad's stereo preamps (models 34 & 44) or some older Steinberger basses (with EMG electronics). There is certain center frequency, here 330 / 1k. When you boost bass, you cut treble and vice versa. You can not use that EQ as a booster (both full) so "smile" type of equalization is not possible. I like it because it gives lots of power in one single knob without overdriving the amplifier. http://www.quadrevisie.eu/quadrevisie.html Have to say that the Stella ("Star") is interesting...

Soft bag (Rockbag etc.): + light weight, cheap, works well at home to protect against dust - cheapo & short lived, faint protection Semi-soft/hard carrying case (like mono): + decent weight, good to carry around, may not withstand airport crew, weather resistant (especially against temperature changes), two bass models available - zippers have lifetime, not so cheap Hard case (like Hiscox or similar): + hard, good protection, repairable, long lifetime, airplane ready (if has the shape of the instrument inside) - heavy, somewhat hard to carry, prices and quality vary Transport case (like Thon or Peli, made of wood and aluminum or polymer): + nearly indestructible, shape keeps the instrument in its place, airport crew compatible, custom made (also for two basses etc.) - heavy and big, may be cumbersome to carry around, on a pricey side

Some might say that George & Leo is the peak of what Leo developed during his years. Idea of an active preamp from StingRay, shapes and basic construction from Jazz and P... would like to say that because G&L is not so known or popular compared to its earlier siblings, it is really good bang for the buck.

Like @Stylon Pilson and @Marc S wrote, it is easier to comment with a question, like: "That was pretty fast, what is the idea behind this tempo?" This gives both sides the possibility to estimate it without direct accusation. Loudness, yes, that is a hard one. If you bandmate has no more hair cells inside his head but just outside, then an easy solution is to take care of the placement of his amp: "Let's put this higher up (and closer to that player), so we can all hear your subtle nuances better..." Sure, you have to take care of the nuances of your comments, too. Remember to be the active starter and example to the others. Go lift that amp and make it happen, do not try to make him do that.

Is there still some bassist who has not visited these pages? Do it now: http://www.ovnilab.com/ If the compressor is somewhat an odd animal, the parameters should be studied, like how attack affects the softness or tightness of the sound. It is good to start from the envelope: ADSR = attack, decay, sustain, release.

If you want to move more air, another similar cab would be the best match for you. Just like Mr. Starr pointed out. + similar sound (you know what you will get) + power is distributed evenly to both cabs (this is an issue, also soundwise) + you can choose between one or two when going to a gig

And your choice for tolerance is 5 % which is gold coded, not something funny like 0.5 %! If you go to a shop or make an order, the resistors need to be metal film ones. They are nearly the same price but superior in quality compared to carbon sH*t. https://www.mouser.co.uk/ProductDetail/KOA-Speer/MF1-4LCT52R473J?qs=91WPSIiQh9LK86gI2c0f1w%3D%3D

It is easiest to solve with a Mohm resistor to ground. Search engine helps here.