Jump to content
Why become a member? ×
  • advertisement_alt
  • advertisement_alt
  • advertisement_alt

Zoom B1 Four


Woodinblack

Recommended Posts

Nice review John!

Given that the HPF and the tuner on the B1-4 should be at least as good as that on the MS-60B and you're getting a tone close to your VTBDI, seems to me you could easily get away without using either and have a one-stop shop in your B1-4.

If you wanted, you could also pick up a compact battery-free passive DI from Behringer for £14. Job done :)

Edited by Al Krow
  • Like 1
Link to comment
Share on other sites

Took the B1X-4 to rehearsal last night.

Used the studio's slightly muddy Ashdown rig. I've tried really hard to like Ashdown RM heads and their cabs but not yet found ones I've really liked;  I guess I've been a bit spoiled by my VK and BF cabs! 

I ended up only using 3 of the original patches: A-wah, Jaco (just for a bit of fun) and Dark Crunch to help cut through with the slightly muddy rig.

But the pedal has had its first outing and it was a very good way to introduce bandmates to their bass player becoming 'effected' 😁

Looking forward to setting up some bespoke patches over the weekend.

Edited by Al Krow
  • Like 1
Link to comment
Share on other sites

2 hours ago, Chienmortbb said:

DI out would have been great but apart from that it looks like a step up from the B1On

Joyo ZGP (courtesy @operative451) to sort out noisy PSU input. Behringer DI (courtesy @jrixn1) to provide a DI out when needed. Total additional cost - around £25

Complete one-stop shop sorted (and add the X-rated wah-pedal version if you want some additional fun)! 😀

 
   

Zoom B1-4 package.png

Edited by Al Krow
Link to comment
Share on other sites

13 minutes ago, Al Krow said:

Joyo ZGP (courtesy @operative451) to sort out noisy PSU input. Behringer DI (courtesy @jrixn1) to provide a DI out when needed. Total additional cost - around £25

Complete one-stop shop sorted (and add the X-rated wah-pedal version if you want some additional fun)! 😀

 
   

Zoom B1-4 package.png

Another numpty question here, I get the Joyo to get rid of noise... will get one to be able the power supply I still having knocking around (Mooer). If I decide to go down the route of using a FRFR cabinet do I need a DI box or can use the output from the B1 Four straight into it...?

Can tell all this multi effect and FRFR speaker is new to me LOL

Thanks

Link to comment
Share on other sites

You'd want a DI box for longer cable runs. There's no "rule" as it depends on many changing/environmental factors - but as a guide, longer than 5m.  The DI box will convert your unbalanced signal to a balanced one, which eliminates interference noise.

So you won't need a DI box for going straight from your Zoom to your active speaker, since it's presumably a short cable.

The time you would use a DI box is if you're running to a front-of-house PA system (but it doesn't sound like you're doing this).
 

  • Like 1
Link to comment
Share on other sites

25 minutes ago, dannybuoy said:

You only need a high impedance input (which are rare to see on mixers) if you're plugging a passive bass straight in. You would be good to plug the Zoom straight into a bog standard line input.

Did you mean active bass dB?

Edited by Al Krow
Link to comment
Share on other sites

20 minutes ago, Al Krow said:

Did you mean active bass dB?

Nope. An active bass, like a preamp or pedal, is not too fussy but prefers to be plugged into a low impedance line input. A passive bass will lose a lot of top end unless it is plugged into a high impedance input.

Edited by dannybuoy
Link to comment
Share on other sites

29 minutes ago, dannybuoy said:

Nope... 

Ok you're gonna need to walk me through that as it seems the wrong way around!

Where an amp has separate 'active' input and  'passive' inputs, the active input is usually a higher impedence input. So, similarly, I would be expecting an active bass to go into a high impedance input on a mixer but a passive bass more likely to be ok not doing so? 

Edited by Al Krow
Link to comment
Share on other sites

Mixers usually just have low impedance line inputs and mic preamps. Sometimes (this is more common on audio interfaces) you might see a guitar input labelled 'Hi-Z' (high impedance).

This is why it is recommended to pair a passive bass with an active DI (like a Radial J48), as they have higher input impedances than passive ones (like a Radial JDI).

I haven't checked impedance specs of many amp inputs though, but would expect them to follow suit. Perhaps labelling can be confusing if an input is simply labelled 'Hi'; it isn't clear if that refers to high impedance, high signal level, or high gain, all very different things!

Edited by dannybuoy
  • Like 1
Link to comment
Share on other sites

Bit of a frustrating evening - downloaded GuitarLab so I could access the Low EQ patch, but unlike ToneLib it just isn't picking up that my B1X-4 is connected up. Ugh!! Probably missed something very basic...

Link to comment
Share on other sites

Are you using the cable that came with it (assuming it did)? If you’re using some random one you had lying around, some cheapo micro USB cables that come with phone chargers only have the power pins hooked up, so can’t transmit data.

Link to comment
Share on other sites

 

4 hours ago, dannybuoy said:

 An active bass, like a preamp or pedal, is not too fussy but prefers to be plugged into a low impedance line input. A passive bass will lose a lot of top end unless it is plugged into a high impedance input.

I've found the following comments on the net.

  1. The active input is "padded", meaning that it has less gain to accommodate active basses with higher output. They also usually have different impedance, but it's mostly high enough so you can plug in either input.
  2. Passive inputs have higher impedance, since its impedance should be 10-times higher than the impedance of the incoming signal. This avoids loss of highs due to impedance mismatch.
  3. An active input generally has -10 db the volume of the passive one (meaning it's half as loud). If you plug an active bass into the passive input and play loud, you'll probably clip the preamp, causing distortion. This doesn't hurt the amp unless you do it constantly, but it usually sounds terrible. Unless you're too quiet, use the active jack.

The second backs up your point, the third ties into what I was thinking, so I'm not 100% clearer on this point! 

Link to comment
Share on other sites

1 minute ago, dannybuoy said:

Are you using the cable that came with it (assuming it did)? If you’re using some random one you had lying around, some cheapo micro USB cables that come with phone chargers only have the power pins hooked up, so can’t transmit data.

Sadly it didn't come with a USB or a PSU!

But your point doesn't quite fit the fact that ToneLib can send and receive data from the pedal via my USB cable, it's just Zoom's GuitarLab that can't.

Link to comment
Share on other sites

7 minutes ago, Al Krow said:

 

I've found the following comments on the net.

  1. The active input is "padded", meaning that it has less gain to accommodate active basses with higher output. They also usually have different impedance, but it's mostly high enough so you can plug in either input.
  2. Passive inputs have higher impedance, since its impedance should be 10-times higher than the impedance of the incoming signal. This avoids loss of highs due to impedance mismatch.
  3. An active input generally has -10 db the volume of the passive one (meaning it's half as loud). If you plug an active bass into the passive input and play loud, you'll probably clip the preamp, causing distortion. This doesn't hurt the amp unless you do it constantly, but it usually sounds terrible. Unless you're too quiet, use the active jack.

The second backs up your point, the third ties into what I was thinking, so I'm not 100% clearer on this point! 

Are you conflating signal level and impedance?

Link to comment
Share on other sites

2 minutes ago, jrixn1 said:

Are you conflating signal level and impedance?

John - very probably, I'm certainly confused 😀

I had assumed that the way that the active input cut the volume by -10dB  compared to the passive input, on a bass amp, was by reducing the signal strength and doing so by having a higher impedance. But that's obviously very simplistic and incorrect.

Link to comment
Share on other sites

42 minutes ago, Al Krow said:

John - very probably, I'm certainly confused 😀

I had assumed that the way that the active input cut the volume by -10dB  compared to the passive input, on a bass amp, was by reducing the signal strength and doing so by having a higher impedance. But that's obviously very simplistic and incorrect.

Yeah, I thought that's where you might be getting confused, they are different things.

A pad is just like a volume control, but on a switch that flicks between 100% and 50% volume, so that you can prevent high output basses from clipping your inputs.

Think of impedance as resistance, and imagine you're plugging your bass into a big resistor. Passive pickups are sensitive to what kind of load they are hooked up to, which is why your bass will sound brighter with 500K pots than 250K ones. In a similar way, the input impedance of an amp or DI will affect the tone of the bass, as that input stage effectively joins up to form one circuit with your tone and volume pots.

Stick a powered transistor amplifier (AKA a buffer, which could be an active preamp) in between the bass and mixer/DI/pedal/amp/etc though, and it will isolate the pickups from the rest of the chain. Your pickups 'see' the input stage of the buffer only, and the tone is then not unaffected by the input impedance of what comes next in the chain.

  • Like 1
Link to comment
Share on other sites

2 hours ago, Al Krow said:

Bit of a frustrating evening - downloaded GuitarLab so I could access the Low EQ patch, but unlike ToneLib it just isn't picking up that my B1X-4 is connected up. Ugh!! Probably missed something very basic...

Took me a while to get it up and running on my PC. I found i had to delete the USB drivers for it when its connected, and then re connect it and Windows would load the drivers again which seemed to do the trick. 

Link to comment
Share on other sites

1 hour ago, dave_bass5 said:

Took me a while to get it up and running on my PC. I found i had to delete the USB drivers for it when its connected, and then re connect it and Windows would load the drivers again which seemed to do the trick. 

Wow, that's effort! You would have thought they would have made it a bit easier than that! 

On the plus side I've had a fun couple of hours on ToneLib creating several bespoke patches. Particularly like the slapback delay :)

  • Like 1
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Recently Browsing   0 members

    • No registered users viewing this page.
×
×
  • Create New...