Jump to content
Why become a member? ×

Recommended Posts

Posted
10 hours ago, Mediocre Polymath said:

I do simple routs like this with forstner bits and chisels – I could easily adapt one of my existing humbucker cavity drill templates if you want to go down that route. Just give me the dimensions.

 

That's very kind of you to offer, thank you. I think I'll give it another go myself and see if I've learned anything from my first go. If it's another mess then I'll be in touch.

  • Like 1
Posted

You can do it perfectly with your router and simple guides locking the motion on the left and right to the desired length of the said router, in just six passes.

Posted
2 minutes ago, Hellzero said:

You can do it perfectly with your router and simple guides locking the motion on the left and right to the desired length of the said router, in just six passes.

 

Reading your message, I just realised my mistake - I was operating the wrong way round.  I should have had my rails/fences/guides on the opposite side, so if I wandered, I wandered into the material I was removing anyway, not the stuff I wanted to keep.

 

FFS!  What a moron.  I really am living up to my username.

  • Like 1
  • Haha 1
Posted

I think I've redeemed myself.  Start again then...

 

33jetstarmodtemplatestartagain.jpg.c9c7d174ebc7286b55d06fa7d42163d7.jpg

 

Made a better jig which actually works the correct way round...

 

34jetstarmodtemplatejig.jpg.92e814d0748eab6a8540f4b7d3f880fe.jpg

 

First cuts...

 

35jetstarmodtemplatefirstcuts.jpg.74c84c486029f0dc9091b9c4f3b819d5.jpg

 

And then changed the jig to do the short sides, et voilà

 

36jetstarmodwaybettertemplate1.thumb.jpg.36d9699e089bc82cab9858c7c2e54703.jpg

 

That's more like it!  Crappy first attempt above for comparison.  Then I guess when you write on it with a Sharpie, it becomes official...

 

37jetstarmodtemplatesharpie.jpg.502ee57c7edbf037612e7f7645e20dd7.jpg

38jetstarmodtemplatefit1.thumb.jpg.def709cbb40fb66599801ef951d9d66e.jpg39jetstarmodtemplatefit2.thumb.jpg.52d4e3d54396c1832adf271f0560281d.jpg

 

The only thing I have to consider is that my top bearing router bit is a bit fat for the corners of the pickup (it's OK for the mounting lugs), had to cut them out after the fact on the template, so going to have to figure out how to solve that.  But progress is progress, and I'm much happier with this second attempt at the template.

 

One final piece of paranoia - I checked that the neck fits when the pickup is mounted - it has a 21st fret overhang...

 

40jetstarmodpositioncheck.jpg.a86679577167791e8e974058de6b59b3.jpg

 

Phew!  That is approximately where the neck pickup of a Peavey T-40 goes with regard to scale length.

  • Like 10
Posted

Found an old plank in the shed to practice on.  Also found a potential solution for the corners - got a 1/4" cutter, if I poke it far enough out of the collet then there will hopefully be enough shaft (stop sniggering at the back, you!) poking down below the baseplate of the router then it should not cut into the template but follow it as if it had a bearing.  Dunno if the radius will be small enough, but it'll be closer than the 1/2" cutter I'll be using for the initial routing.

 

41jetstarmodoldplank.thumb.jpg.7eacd488c37ab1f0a46b86740da4742e.jpg

 

That's tomorrow's fun though - got a band rehearsal now.

  • Like 6
Posted
47 minutes ago, SpondonBassed said:

Things don't always go right the first time.  Well done for keeping at it!

 

Exactly what Mrs S said to me a couple of nights ago... :ph34r:

  • Haha 6
Posted

So I found a nicer piece of pine to practice on than that scabby old thing I found.  It went... OK.

 

42jetstarmodtestrouteforstner.jpg.598fe9dfbaa92c96aef8564f6bcf3484.jpg

43jetstarmodtestroutecomplete.jpg.76227eb70d77ca8f1ff674bd5b090ca4.jpg

 

A few wobbles (including setting the depth of my cutter a tad low at the beginning.  But lessons learned, and praise be, the pickup fits (using the 1/4" cutter in the corners).

 

44jetstarmodtestroutepickupfits.jpg.7f5f665fe53383cf78d76f99cc4cd177.jpg

 

I thought about having another test run, but I thought "F it" and decided to proceed directly to the real thing...  First off, remove the bulk of the hole with the drill and forstner bit.

 

45jetstarmodpickuproute1.thumb.jpg.b9e4f0b874e6cdb3893cf82cda107481.jpg46jetstarmodpickuproute2.thumb.jpg.1fae0cf9683669583097d33ef520d649.jpg

 

Then deep breath and get out my most hated power tool, the router.  Took my time this time, double checked everything.  Did the main shape with the 1/2" cutter, then swapped to the 1/4" cutter for the corners.  Howzat?

 

47jetstarpickuproutedone.thumb.jpg.222a2eacfdf32eb0fec43f0c496b4c28.jpg

 

The wee deeper holes in the corner are because I had to poke the 1/4" cutter down sufficiently so that enough plain shaft was below the baseplate so it would not cut the template.

 

IT FITS, YAS!

 

48jetstarmodpickupfitting1.jpg.b066abb046f3b52b054d107db8a73642.jpg

49jetstarmodpickupfitting2.jpg.d66e763a6a5c4db037098c9d4050b09b.jpg

50jetstarmodpickupfittingwithneck.jpg.2c7865014c35f74afbce12753b49b203.jpg

 

I am very pleased with my afternoon's work.  This is the first pickup route I've ever routed in my life.  Glad it went well, but won't be sorry if I don't ever do it again, lol.  It most certainly has not "given me the bug" - it was stressful and horrible work, but I am very pleased with the results.

 

Next job - figuring out how to make a dirty long hole from the control cavity to the pickup route without ballsing the entire operation up.  I might need a bit of professional help with that so I might pay the Engineering Workshop at work a visit on Monday and see if I can cadge a disgustingly long drill bit at the very least.  Or they might take pity on me and do a "give it here" - I won't complain!

  • Like 8
Posted

I’m over the moon for you with that - great work mate. 
 

The test run - that’s a step I’d skip (and f*** up thereafter)

 

bass looks mint x

  • Like 1
  • Thanks 1
Posted

The easiest way would be to drill a hole from the neck pocket through the neck pickup cavity to the bridge pickup cavity.

 

Fast, easy, clean, invisible, impossible to screw.

  • Like 1
Posted
1 hour ago, Hellzero said:

The easiest way would be to drill a hole from the neck pocket through the neck pickup cavity to the bridge pickup cavity.

 

Fast, easy, clean, invisible, impossible to screw.

Impressive work, Neep. As for the cable run, see above.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
×
  • Create New...