PaulThePlug

Nice... Wurther's Original Butter Candy...

All Wired-Up!.. Vol(A500k)/Blend(MN500k)/Tone(Aretec QTP)... ...and might go for a DFA/Producer Switch in the empty hole...

Might have a shim under the bridge bar or piezo element? But, likely to just get a load of buzz higher up, need to have a look at the relief before nut and action. 1mm or so might be good for a heavy strummer, but 2mm sounds like making issues for string height, intonation etc. Action 2mm at the 12th... but not relief 2mm at the 6th String Gauge?

Pickup Foam finally turned up... out of the cover... Double-Coil Deep ... and, hanging out of the cover... hence the trench. Now... Do you think i could find a matching set of 8 screws? Even if old, think they deserve matching after all it's put me through... So currently 2 'n 2 while i get on the case...

Vary... Yep... But as long as the existing screw holes get covered... On a budget? - take a look at Aliexpress - some funky Colours, Swirls and Pearls... Also the pickup foam - with a little spring in... Wax Cloth Wire... If you haven't got a Jack Socket yet, I rate the Pure-Tone Multi Contact.

Calling 3D Printer People!...

Love the Adagio flats on my Harley B Acoustic Bass... Real woody upright tone Had bronze on there to start with, too squeaky for me... Ah... Just noticed... 'Short Scale' Was some short scale flats FS on here... unless ya don't like flats...

Best Bass is the one you want to pick up...

Oh My... Nice... https://www.musicplant.co.th/en/product/82040/umedaujb4norathep-masaeng-signature

More... ^ I recall a thread where the Headstock was done before the scratchplate was lifted... and hole noticed... so no return, that said it's real little and a sticker, or plastic wood type fill would sort it... Fingers crossed yours hasn't but not end of world stuff.

@police squad... STOP... Been a few HB PB50 Modders about... and does look like a mighty fine 'lil project... Earlier(?) ones have no routing under the plate, later ones have had a small hole in the top... to make the drilling and wiring easier between pup cavity and control cavity via the hole... shame - or a little sticker? 😉 The burst on the later ones is a paper photo burst over bass wood... some posts pics etc show and describe lots of plastic type sealer... bugger to get off - Red one is meant to be an easier re-fin Headstock?.. see page 6 Mike Dirnt - still tempted to tele the head on my P Bitsa...bass heads.pdf

I think the Strat proximity was for swells... Knob, Jazz, Technique... all in one sentence?... Maybe one of those up and coming strange Maths-Jazz-Infusion enthusiastsm

@Duarte... about time!.. Following with interest. Remember seeing seeing this, was the inspiration for my Custom J PJ Body.

Ibanez SR300...

Or... Think this was Fenders Idea when QC took a dive...

Just for round the neck pocket sides, maybe the back as well, the depth of the neck pocket... piece like this do ya?.. 180mm x 25mm... PM me an address and i'll pop it in the post cardboard protected. It's very brittle and thin... a dab of lemon oil may help, but might effect the glueing. I'd glue then trim.

Veneer... 'Prolly able to get away with a 'sample' often sold for a pound or cost of letter post. Hold the page... off to the shed... Remembered i got sample to do a TRC on my Rick-a-like but the veneer was too thin, for the size of cover..

Sometimes the serrated lock washer, if used... can cut through the foil, or paint, reducing the effectiveness of the contact... so a link of stretched TCW is a good call, or run all grounds to the Jack... easier with a simple single pup less wires... dont forget the bridge earth. EDIT: Sometimes the serrated lock washer, if used... can cut through the foil... Meant the foil on the back of scratchplate, not copper foil lining of a cavity...

Fixed it for ya...

At the time and my youthful music No... Fats Domino, Everly Bros, Buddy Holly, Duane Eddy... Nowadays when i hear em, it takes me straight back and i can appreciate whats in them.

What sort of Twin P Configuration? It's just for fun... or is it? 😉

In 2015 it was $600 v's $465 list for an SR300... B300 instead of B120 Bridge, and a Coffee Table Top. Think i might out the 3 Band and try the Pups Passive VBT...

Autosol Dremmel Polish of the Frets and Lemon Oiled the Light-ish Rosewood Fretboard... Nice Bees Wax and a Buff... Claro Walnut finish is described as Natural Gray Burst Flat... Subtle Few dings and some wear and tear...