Jump to content
Why become a member? ×
  • advertisement_alt
  • advertisement_alt
  • advertisement_alt

Making a solid body hollow


rapscallion
 Share

Recommended Posts

I had similar done last year on a wrecked Bass Collection bass. Top 6mm was planed off and new face glued on. You could have the same done and route out cavities before putting the new face on. No problem for any decent luthier.

Link to comment
Share on other sites

From my experience, cutting something that wide could only be done on a (very large) bandsaw. The annoying thing about bandsaws is that the bendy blade tends to wander from your intended straight line, and the cut itself tends to be quite corrugated. By the time you have cut the top off and then made both faces perfectly flat, you'll have lost an unacceptable amount of depth.
If you really wanted to keep the top, you'd probably need to add an inbetween layer to make up for this loss.

One of the above methods makes a lot of sense - put the body through a thicknesser and take off the appropriate amount (maybe 8mm?) which will leave a perfectly flat face. Then chamber and stick on a new top.

Edited by Roland Rock
Link to comment
Share on other sites

I saw something on the internet the other day (sorry can't find it now) where a Telecaster was chambered out from the back (leaving the centre block for strength and pickups etc) and then had just the routing covered over.The guy did it with plastic, like a pick guard - he'd cut a small lip on the edge of the routing so that the guard was flush with the body, but if you did this with wood instead of plastic you could then paint over it and no one would be any the wiser and it would be a lot easier than cutting the guitar in half. He also put an f hole in it to make it a thinline.

Edited by 6feet7
Link to comment
Share on other sites

  • 3 months later...

[quote name='6feet7' timestamp='1403170578' post='2480377']
I saw something on the internet the other day (sorry can't find it now) where a Telecaster was chambered out from the back (leaving the centre block for strength and pickups etc) and then had just the routing covered over.The guy did it with plastic, like a pick guard - he'd cut a small lip on the edge of the routing so that the guard was flush with the body, but if you did this with wood instead of plastic you could then paint over it and no one would be any the wiser and it would be a lot easier than cutting the guitar in half. He also put an f hole in it to make it a thinline.
[/quote]

Sounds cool and cost effective. Unless you have a particular upgrade in mind (e.g. using flame maple on the front) breaking the finish all around the edge and redoing the pickup, bridge and control mountings (depending on route locations) is a fair amount of work. I'd go in from the rear in this case... that sounds a little smutty when said aloud.

Link to comment
Share on other sites

[quote name='rapscallion' timestamp='1402997513' post='2478587']
Hi guys,

Would it be possible to plane off the top of a guitar body and route out the cavities to make it a semi, then just glue and clamp the top back on? Am I just completely missing the point or is this a viable option?

Cheers
[/quote]

Basically how I built my thinline telecaster with one exception:The top of the guitar would definitely have to be sacrificed to do it properly, short of a massive industrial bandsaw you wouldn't get a straight enough cut to re-use it. However it meant I could put a nice new flamed and spalted maple to on what was an otherwise very plain body (the back and sides were painted cherry red with sunburst finish on the top + cream binding).

Routing out from the back and using cover plates is probably the easiest thing to do if it's for a quick & dirty modification to a cheapish guitar. Making a custom pick guard could work but would never be my first choice for reasons of aesthetic preference.

Neck dive could be helped by moving strap buttons if possible or putting counterbalance weights in the tail end if required.

Think carefully about where you're taking strength out of the body with the router - I would recommend that you leave a fair amount of core material down the centre and around mounting points for the neck & bridge.

Edited by Bradwell
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

 Share

  • Recently Browsing   0 members

    • No registered users viewing this page.
×
×
  • Create New...