WarPig

[quote name='jjl5590' post='174153' date='Apr 10 2008, 08:42 PM']ok, i've decided to stick with a GK cab. should i get 2 of these: [url="http://www.gallien-krueger.com/products_artist_ca_210rbh.html"]http://www.gallien-krueger.com/products_ar..._ca_210rbh.html[/url] or 2 of these: [url="http://www.gallien-krueger.com/products_artist_ca_neo212.html"]http://www.gallien-krueger.com/products_ar..._ca_neo212.html[/url] i want to try and get pretty close to the tone flea has (without his bass of course)[/quote] If your willing to spend a grand on 2 of the neos [url="http://www.guitarampkeyboard.com/en/neo-212/68568"]http://www.guitarampkeyboard.com/en/neo-212/68568[/url]

I want to fit one to my aerodyne, but im not sure on which one to get.

If you used 'I have 2 x 10" drivers... they are rated at 150w and 4ohm....' the overal ratings would be 300w and 2ohm. The 2 ohm would damage the head. If i was you id replace the broken driver with one of the same ratings.

[quote name='DHA' post='171988' date='Apr 8 2008, 05:05 AM']It depends on how this one goes. At present I have sold zero, so not looking good. Dave[/quote] Oh, well it'll be one in +/- 5 days when my paypal funds clear!

Will you be offering kits for any other pedals in the near future?

[quote name='thewalruswaspaul' post='171882' date='Apr 7 2008, 10:54 PM']Thanks Warpig, Its nice to have someone actually answer my question instead of slagging off the bronco , did you have to do any mods to get the SCPB-1 to fit ? .[/quote] Thats ok mate! Just needed to sand abit of the pick-up hole out, and use wider screws for the adjustment holes.

[quote name='jjl5590' post='171269' date='Apr 7 2008, 11:38 AM']True, I could, but then that would only be a half-stack, and I doubt will be loud enough. Don't you mean two 8ohm 210s? (The Hartke amp is 4ohms, anyways)[/quote] Did you start out as a guitarist? Go to a few local rock gigs and check out the bassists rigs, and you'll soon see that alot of people dont need 2x 4-10's. 2x2-10's is definatly loud enough.

I stuck a Seymour duncan SCPB-1 in mine made a world of difference. Ignor the haters! Oh and any rail type pick up will work on a bass, its the same principal electronic wise.

[quote name='Crazykiwi' post='170643' date='Apr 6 2008, 12:18 PM']how much buffing did you do between coats?[/quote] i went over the primer with either 1200 or 1000 wetted. then the final coat again with the same grit.

Thanks everyone! It was just plastikote spray paint, my first attempt at it, i dont think ill be doing it again though.

If it was mine id go for the red tort, but im just following orders hehe

[quote name='BassManKev' post='170460' date='Apr 5 2008, 09:45 PM']odb-3, good man hows the bass chorus?? i might get one[/quote] The chorus is my first one so i wasnt too sure what to expect but after some testing its just what want, subtle but with some tweeking it can take over [quote name='BassBalls' post='170499' date='Apr 5 2008, 11:43 PM']Yeah the ODB-3 is pretty cool. Defiantly kept the low end well. It did most things for me from a light drive to a full on bumble bee fuzz![/quote] Yes! Exsactly! Alot of people talk bad about it, but i find it suits the sound im after. The sansamp is on 90% of the time though.

Well i finally completed it today, after many mistakes and loss of interest.... I dont have any good pics of the original, just the sanded down body. Its a Jim Deacon type 'no-name' Strat. After Sanding: Final:

Very basic board so far, saving space for a 105q. And the rack stuff:

Nearly done modding mine Just need the gold strings The bandmates have coined it 'the bling bass'

45-65-85-105 although i want to go heavier.

Yes it will all work together. It is fine to use the 4x10 by itself, itll just be abit quieter. Wheels (Castors) can be bought at any hardware place like B&Q, and installed by someone with some DIY knowledge. IMO the marshall stack will be better in the long run because the cabs can take more wattage, so you could always upgrade the head when you feel the need to. Abit of De-Ja-Vo there

My TU2 tunes my low b very well, i even dropped it to F# and it was ok, just a bit slower tracking.

[quote name='Alfie' post='166946' date='Mar 31 2008, 03:44 PM']Personally I would prefer not to have a drilled enclosure so that I can add a bit more of my own personal touch.[/quote] +1 Only takes a little bit of time to DIY. Maybe you could offer both non drilled and pre drilled cases?

[quote name='ahpook' post='166635' date='Mar 30 2008, 11:29 PM']do you find that as the signal level drops, the overdrive sounds suddenly disappears ?[/quote] Erm never had that problem, maybe your's was faulty