Jump to content
Why become a member? ×
  • advertisement_alt
  • advertisement_alt
  • advertisement_alt

two cabs 8ohm and 4 ohms


tkelly150
 Share

Recommended Posts

You could use the separate left and right speaker outs - one for each speaker, but as Chris has already said, running them in parallel (two speakers from the same output) isn't safe to do. 

 

You'll notice that your 4Ω cab is MUCH louder than the 8Ω, as it allows the full 250W to be delivered to the cab, but it's possible.

 

Another way to do it would be to run it in Bridged mode (8Ω minimum) with the cabs wired in series (giving you a 12Ω load), but you'd need a specialist cable to do that as it would need to run:

 

Amp hot ->8Ω speaker hot, 8Ω speaker ground -> 4Ω speaker hot, 4Ω speaker ground -> Amp ground.

Edited by paul_5
  • Like 1
Link to comment
Share on other sites

50 minutes ago, paul_5 said:

You'll notice that your 4Ω cab is MUCH louder than the 8Ω, as it allows the full 250W to be delivered to the cab, but it's possible.

Really... we are talking about few decibels... if the 4 ohm version is much more sensitive, I'd buy that. Otherwise not.

 

Sometimes an 8 ohm impedance speaker may be louder than a 4 ohm counterpart.

  • Like 2
Link to comment
Share on other sites

15 minutes ago, itu said:

Really... we are talking about few decibels... if the 4 ohm version is much more sensitive, I'd buy that. Otherwise not.

 

Sometimes an 8 ohm impedance speaker may be louder than a 4 ohm counterpart.

Fair point, it’s just my experience with my cabs. The 4ohm cab IS more sensitive though.

Link to comment
Share on other sites

2 minutes ago, itu said:

Sometimes an 8 ohm impedance speaker may be louder than a 4 ohm counterpart.

Quite right. Impedance alone doesn't define how loud a cab will go. It has nothing to do with power. The reason a 4 ohm speaker will go louder than an identical 8 ohm speaker is excursion. An amp at the same settings will deliver the same voltage into both, but the excursion of the 4 ohm speaker will be longer, so it will be louder. The fly in the ointment is if the speakers are identical other than impedance. They almost never are. If you compare the T/S specs on the Eminence Kappa 15A and 15C, one of the very few drivers made in 4 and 8 ohm versions, the rest of the specs aren't the same. Even the DCR isn't doubled from the 4 ohm to 8 ohm versions, they're 3.68 and 5.22 ohms respectively. Most significantly, the xmax of the 4 ohm is 2.44mm, that of the 8ohm version 4mm. That being the case the 8 ohm can go significantly louder than the 4 ohm.

  • Like 1
Link to comment
Share on other sites

On 19/05/2023 at 19:22, paul_5 said:

You could use the separate left and right speaker outs - one for each speaker, but as Chris has already said, running them in parallel (two speakers from the same output) isn't safe to do. 

 

You'll notice that your 4Ω cab is MUCH louder than the 8Ω, as it allows the full 250W to be delivered to the cab, but it's possible.

 

Another way to do it would be to run it in Bridged mode (8Ω minimum) with the cabs wired in series (giving you a 12Ω load), but you'd need a specialist cable to do that as it would need to run:

 

Amp hot ->8Ω speaker hot, 8Ω speaker ground -> 4Ω speaker hot, 4Ω speaker ground -> Amp ground.

You can get a small box especially made for combining speaker in either series or parallel to one amp  speaker/cab output, like this one, the Palmer CAB M Merger :

preview.jpg

Doesn't cost much either, a mere 26£ : https://www.thomann.de/gb/palmer_cab_m_merger.htm

 

Edited by Baloney Balderdash
Link to comment
Share on other sites

IMO those little boxes are not safe to use with a high power amplifier. The 1/4" phone sockets are simply not up to the current/voltage needed. They were originally designed for telephone switchboards operating at 48V DC and a couple of hundred milliamps. That's far below what a typical bass amp puts out.

 

if they had used SpeakOns I would have no objections. :)

  • Like 1
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

 Share

  • Recently Browsing   0 members

    • No registered users viewing this page.
×
×
  • Create New...