6feet7

Standard 151HR - Made in Italy Product code: MBL100039Y SPECIFICATIONS: Power handling 400w Series Standard Size L Speaker config 1x15" Impedance 8ohm Tweeter 1" driver w/horn Tuned port Rear FIND A DEALER TECHNICAL FEATURES IMPEDANCE 8 ohms SPEAKER SIZE 1×15 in. BASS PORT rear TWEETER 1″ compression driver with custom horn POWER HANDLING 400W RMS (AES Standard) CROSSOVER FREQUENCY 3.5 kHz FREQUENCY RESPONSE 40 Hz to 20 kHz SENSITIVITY 100 dB SPL WEIGHT 47.84 lbs / 21.7 Kg WIDTH 23.23 in. / 59 cm HEIGHT 23.54 in. / 59.8 cm DEPTH 18.98 in. / 48 cm

I got this in a part-ex from Bass Direct in January (and I love it) but I've got my eye on something, so even though I'm losing a couple of hundred £ in two months it's got to go. Alder body, fotoflame top, maple neck, rosewood f/b, 2 band eq. Comes with a slightly battered Fender hard case. •Weight: 8lb 15oz/4.0kg

PM’d

Oh, I love these. I've had 3 (2 Korean and 1 German). And I'm in Rugby tomorrow morning. Decisions, decisions..............

I bought this as I couldn't find my Lehle ABY pedal, but as soon as this was delivered and put on my pedal board I found it, so this has never been used. Post at cost Fender's ABY footswitch with passive switcher allows you to plug a single guitar into two amplifiers or plug two guitars into a single amplifier, making it easy and convenient to create a rig with eminent flexibility and a variety of tone options. True hardwire bypass in the off position lets players retain their natural tone without interference or signal loss. "A or B" and "A and B" switching options allow for greater versatility within your rig. Durable metal chassis and switches withstand onstage wear and tear. LED illumination requires 9-volt battery or power source. Velcro on the back In original packaging.

I had this when I owned a Rickenbacker and it totally eliminated all the hum. Absolutely eliminates hum from any audio source. Not a noise gate and not a suppressor. Dead silence in your signal chain courtesy of a little EH magic. True bypass Tough and compact die-cast chassis 7.5AC-400 power supply included Velcro on bottom Original box. Post at cost

Electro-Harmonix Bass Preacher Velcro on the bottom. Hardly used. Original Box. Post at cost Quick Specs - Compact compressor designed especially for bass guitar - Input sensitivity ranges from -10 dBu to +2 dBu making it a perfect fit for both passive and active basses of varying output levels - Maximum gain reduction of 21 dB, with enough make-up gain to return your signal to full volume at maximum sustain (compression) - Attack toggle switch changes the timing of the onset of compression and provides three selectable settings: Fast, Medium and Slow - True bypass for maximum signal path integrity when in bypass mode - Tough, compact die-cast package - Dimensions in inches: 2.75 (w) x 4.5 (l) x 2.1 (h) - Dimensions in mm: 70 (w) x 115 (l) x 54 (h)

Price drop to £675 as this has to go to help me pay HMRC Used but not abused. £300 worth of Aguilars fitted. Original Bartolinis included. That awful locking jack was replaced with a normal one (before I bought it). Also it looks as if the front strap button has been plugged and refitted. Non original gigbag. Chambered Body: Basswood Bolt-on neck: Maple/walnut Fretboard: Roasted birds eye maple Abalone off-set dot fretboard inlays Multiscale scale: 838 - 889 mm Fretboard radius 500 mm Nut width: 45 mm Plastic nut 24 Stainless steel medium jumbo frets Pickups: 2 Bartolini BH-2 humbuckers Electronics: Varimid 3-band EQ Controls: Volume, Balance, Treble, Mid, Center Frequency, Low Switch: EQ bypass MR5HS bridge

BUMP

I’ve seen these before, and the tuner routing etc would be easy. It’s just a shame it isn’t a couple of mm wider at the nut end.

I love these. Wondering whether I can convert it to a 5 string with that 42mm nut?

38cm x 38cm A couple of years old. Never gigged. Postage included in price.

Mensinger Joker B5a, 30” Dragons Breath finish, flamed maple top 1. New Mensinger Joker, a first class set-neck, chambered bass made with a chambered mahogany body, quilted maple top top, Ebony (Catalo) fingerboard, Dual coil pickups. 2. Weight: 9lb 8oz/4.3kg 3. Specifications; 4. Body: chambered mahogany body, Flame maple top 5. Neck: 3 pieces hard rock maple, 30” scale 6. Fingerboard: Rosewood, 24 frets 7. Nut width: 45mm 8. Construction: set in 9. Pickups: Bartolini Dual Coils 10. Electronics: Passive: Maruszczyk Toneformer, three band eq, the treble control becomes a passive tone control in passive mode. Active/passive switch from master volume 11. Finish: Satin Dragons Breath, body/neck matte 12. Hardware: Black, ETS bridge with 18mm string spacing, ETS knobs, 13. incl. logo'd Gigbag

I bought this earlier this year (used from B.D) but I haven't used it as it's more powerful than I'll ever need down the 'Dog n Duck' and it takes up too much space just sitting here collecting dust. Postage may be a problem, but get in touch and I'm sure something can be worked out.

I'm still not clear if this is the MS or SMS version. A photo of the back of the 'headstock' may have this printed on.

Bump

BUMP

BUMP

I’ve had both the Korean and this model German ones. Absolutely gorgeous basses.

Can you tell me the width of the nut (and string spacing). Love to do a 5 string conversion

I bought this last month for £2199 from Bass Direct but I owe HMRC more than I happen to have, so it has to go. Mensinger Joker 5a, 30” Two Tone Sunburst - new and unused. Specifications; Body: chambered mahogany body, Flame maple top Neck: 3 pieces hard rock maple, 30” scale Fingerboard: Rosewood, 24 frets Nut width: 45mm Construction: set in Pickups: Delanos Electronics: Passive: maruszczyk Toneformer, three band eq, the treble control becomes a passive tone control in passive mode. Active/passive switch from master volume Finish: Satin, body/neck matte Hardware: Chrome, Mono Rails with 18mm string spacing, ETS knobs, incl. Gigbag and paperwork etc