SpondonBassed

Welcome Ricky.

Welcome Spencer.

I have just started using Tuxguitar to write some TAB from some scrolling YT clips. Interestingly, it writes standard notation as you enter in TAB. It is much easier for me to use than Guitar Pro. I couldn't get the hang of that somehow. I had to pay for it too. Tuxguitar is free. I wondered if there was any love out there for Tuxguitar. PS: I should mention that this is on the Linux platform

Once again, Dave has demonstrated great kindness and generosity by sending me some more goodies. A preamp and a pickguard all at his own cost. Securely packaged and in top condition. Much appreciated Dave!

PMd

Welcome Mark.

Not the middle. Think of where you see the most adjustment for correct intonation - the E string. The least amount is the G. The scale length is 34 inches. None of the strings will have an effective length shorter than that. If you measure with the saddles centred, you lose potential adjustment. What I do is to set the saddles to minimum adjustment (assuming all saddles travel the same amount). That is; all saddles set as close to the nut as they can go without loosing sight of the threaded end of the adjustment screw inside the saddle. You need all of the threads to be engaged for best contact between the threads of the adjustment screw and the saddle itself. I then measure from the point of contact on the saddle to the nut and mark off the body at the bridge datum to give 34 inches of string length between point of contact at the nut and the saddle. You then have max adjustment potential for each string.

Welcome Henning.

Welcome Mike, Hang on for a decade or so while I go around and ask everyone for you... Heeheehee

Development in the field. Wow. Beat that!

You keep your gourd based instruments to yourself young man! I'm warning you. I'm deadly with a root vegetable.

Okay. Thank you for, er, filling me in as it were. I don't like the idea but as long as there is no asparagus involved I'll try anything once. I'm GASsing for a USA Stingray.

All right all right, which one of you lot broke Jack? He don't sound so happy now.

If by AI, you mean Artificial Insemination, then it may well be a cure for The GAS. Before you know it you'll have lots of little basses just like @Jabba_the_gut's biting at your ankles.

Is it "What's better than five of nine by a good pair"?

As has been said by @Andyjr1515 among others; part of the pleasure of doing this is being able to take time out to work out the best way to achieve a desired result with what you have to hand. It's easy to get caught up in a wave of enthusiasm and then go kak it up. For the sake of a little restraint all the work to that point might as well be written off. I've been trying to work out by eye how to conceal the East's long PCB behind the existing control panel cover by removing just enough wood to make it slot in obliquely across the cavity. I stopped to think how best to choose the exact centreline for the PCB before I start the cut. Using the amp itself is not a great idea because of the risk to the soldered connections through repeated bending of the many wires during the trial fits. I needed a gauge that represents the loaded PCB dimensions closely enough to serve throughout the job. I started with a baton of the same thickness. Then I traced the outline of the PCB allowing for a little over where some wires exit from the end of the board. A few cuts with the tenon saw and a quick rub on some Abranet and we have a gauge. That's all I can get done today. I am exited so it's perhaps for the best. It'll allow a bit of time for me to cool off.

Excellent! I would've worked it out step by step but that encapsulates it all nicely for me. Thank you. Now I can work out why the Ray34 eats batteries unless you disconnect it despite being unplugged as well.

Maybe you aren't quite ready to hand saw a chopping board from the back of a P bass but you are well on the way.

I like that a lot. There is something satisfying about a good mitre joint. What angles did you use?

It's known as The GAS in these here parts. Welcome to the forum DP.