Jump to content
Why become a member? ×
  • advertisement_alt
  • advertisement_alt
  • advertisement_alt

Wiring...a quickish question.


NancyJohnson
 Share

Recommended Posts

I have an 80s Ibanez Roadster project.  Twin pickup model (P/J); if you're familiar with the model you'll recall it originally carried an active circuit - which was long gone when I bought the bass - it currently looks like this:

 

20220111_220027.thumb.jpg.25546190e2eaa6168aeb0f15702e4b3f.jpg

 

At present, each pickup is wired into a volume pot, then into a selector switch (predominantly so I could just isolate the P-pickup), but at some point I want to wire a tone pot into the circuit.

 

I'm wondering whether I might get something different tonally if I wire each pickup to its own tone pot, then into the selector, then out to the output jack. 

 

More Rickenbacker stylee than Jazz bass.

 

Opinions?

  • Like 1
Link to comment
Share on other sites

14 hours ago, PaulThePlug said:

Nice... 2 tone pots and maybe 2 cap values...

Have a look at Rick v's Les Paul wiring...

Maybe the Artec QTP 1, with a conventional tone, or 2?

 

Because this is a bass that's not so important in the scheme of things, I don't mind throwing a little money/time at it in the spirit of exploration.  Wiring it VT/VT > switch > output jack, should give me different tonal characteristics/properties than going the V/V/T route and applying a singular tone over both pickups.  (I have five holes in the front of the bass so I figure I can just fill them up with knobs, why not?).

 

I need to go through my box of spares.  I know I have some .047 caps.  Not sure whether I have any CTS 250K pots.

 

 

 

Link to comment
Share on other sites

Les Paul wiring is known to "couple" the volume controls together, where they both affect eachother and the overall volume with the pickup selector set to the middle position. If you want true independent volume and tone controls, there is a workaround to it but it will affect the treble response of the bass:

 

https://www.premierguitar.com/diy/mod-garage/les-paul-independent-volume-wiring

Link to comment
Share on other sites

54 minutes ago, LeftyJ said:

Les Paul wiring is known to "couple" the volume controls together, where they both affect eachother and the overall volume with the pickup selector set to the middle position. If you want true independent volume and tone controls, there is a workaround to it but it will affect the treble response of the bass:

 

https://www.premierguitar.com/diy/mod-garage/les-paul-independent-volume-wiring

 

Oh yeah, if I ever used both pickups together, I would find this most frustrating, but my bridge pickup is pretty much there for show.  Hence why my "poker chip" is labelled DO (neck) and DO NOT (bridge).  Note that, as Yoda says "there is no try" (because I don't use the middle setting at all - I've yet to find a bass where the middle setting isn't the worst one, to my ears the two pickups fight and suck the life out of each other, resulting in a rather characterless, plain tone which I do not enjoy).

Link to comment
Share on other sites

1 hour ago, neepheid said:

 

Oh yeah, if I ever used both pickups together, I would find this most frustrating, but my bridge pickup is pretty much there for show.  Hence why my "poker chip" is labelled DO (neck) and DO NOT (bridge).  Note that, as Yoda says "there is no try" (because I don't use the middle setting at all - I've yet to find a bass where the middle setting isn't the worst one, to my ears the two pickups fight and suck the life out of each other, resulting in a rather characterless, plain tone which I do not enjoy).

 

I've always preferred the tonality of a twin-pickup bass; all my kit is set up to allow the ease of just playing with everything full-on or open tonally.

 

 

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

 Share

  • Recently Browsing   0 members

    • No registered users viewing this page.
×
×
  • Create New...