Jimothey

Oooohh errrr missus 😁

I haven't decided if I am being very brave or very stupid as yet 🤨

Whack a couple of magic tree's in your car that will take the smell away 😁

I really liked the sound of a binding so I've decided to bind the neck and headstock with some Oak veneer I've got Also it's covered the discrepancy which is a bonus I'm going to leave it all clamped up till I'm back in work on Friday the start shaping and sanding everything 😀

I think that's what I'll do as it is only for me As per usual I'm overthinking it!! 🙄

That is my main concern but I can't see any other way at the moment? Maybe when I radii (I think that's the right word?) the neck most of it might be removed? 🤔

Thanks but I had a bit of an accident today, routers and hay-fever don't mix! half way through routing the neck blank my eyes started streaming and had a sneezing fit and before I could switch the router off I nicked the neck near the nut 🤬 So the only thing is I can think to get over it is if I carefully rout the neck 6mm thinner on each side (which is the width of the Oak strip wood then glue it on)

Thanks mate I've just got to finish doing the tapers then I'm ready to glue the wings on 😀

No Woodinblack is right it didn't adhere well at all I probably should have used a different glue but I swapped it for Oak instead 😀

Got a bit more done today, Headstock cut started to redo the taper and took some of the bulk off the back of the neck aswell

No worries it should already be to the correct size, when you print it click it actual size and click poster then it will print out multiple sheets

I don't know how authentic these plans are but maybe this might help or at least point you in the right direction? https://sites.google.com/site/guitarplanscollection/pdf-files/fender-ish The top two are 51 P Bass body and neck pdf's

They both sound interesting, Basses with LEDs isn't really my thing but I'd be interested in seeing how you do it and how it turns out?? I'm really not keen on fret dots either I much prefer a block! I'm not sure on this build to whether to try and do the blocks out if the veneer I'm going to use or leave the fretboard plain? What you going to cover on the podcasts?.......

Intriguing!?! What's the project then??? 🤔

Well it's official Sapele, Polycarbonate and Gorilla glue not a good combo!! I thought the neck was solid but NO!!!!! It's just split when I was gluing on the wings 🤬 So last minute alteration I found some Oak strip wood so the neck is now Sapele and Oak I'll have to redo the taper when it's dry then glue on the wings... But if I do say so myself it was starting to looking good 😁

Morning I've routed out for the truss rod with a 6mm bit and went just a smidge over 9mm deep, and I've thinned down the wings to 35mm Hopefully on my lunch I'm going to do the taper of the neck and try and get the wings all glued on Here's the link for how stewmac tell you to fit a truss rod https://www.google.co.uk/url?sa=t&source=web&rct=j&url=https://www.stewmac.com/How-To/Online_Resources/Learn_About_Truss_Rod_Installation_and_Repair/Truss_Rod_Installation.html&ved=0ahUKEwis2pv-6NjbAhWEA8AKHR8NB8UQFggnMAE&usg=AOvVaw2OroVE96fn1E7jqIdJMHNX 😀

Cheers for the advice and pics if it's good enough for you I'll take it!! 😁 I read on stewmac's website to fill the sides with epoxy but reading your explanation not gluing it at all makes a lot more sense! So I don't mess it up the one I've been looking at is 6mm wide x 9mm height if I thinking correctly when I rout out the channel it needs to be a tight fit?

Cheers mate just out of interest what glue do you use to stick them in normal wood glue or epoxy?

+1 Awesome!!!

I just thought it would make it easier Ref the truss rod the shortest I've found that should work is a 435mm one which comes to here? To me that should work perfect but I still would prefer some advice on it 😀

I think this shows it better how I'm going to do it I asked that question on this thread and started one on the repairs/technical and just got told that the truss rod needs to end at the end if the fretboard But I asked the same question as you surely it doesn't need to go a lot past the torn horn as the neck can't move beyond that point anyway??

That's just a mock up I've decided just to taper the whole neck then glue the wings on as it looked a bit odd when I set it up with the neck left parallel when it meets the body but I'm not ready to glue up yet I still need to rout out for the truss rod Which I'm still not sure what length I need it to be?

Yeah before I glued up the laminations for the neck with a utility knife I criss-cross scored the polycarbonate then glued it together and it seems (🤞) to be holding But I think a strongly worded email is needed to gorilla glue STICKS EVERYTHING MY derrière!!

I think that the surface of the polycarbonate is too smooth so the glue isn't getting a very good/strong key to it I don't think I scored it on the body laminate but I definitely did on the neck??? 🤔

Couldn't get as much as I hoped done! Marked out for the taper and truss rod and cut the wings, but............ For some reason the neck is completely solid but the body split apart (Note to self maybe the polycarbonate might not have been a good idea..... But at least I tried!?!) so luckily I had some more sapele which is 44mm thick so I've used that and a going to plane it to about 38mm