Jump to content
Why become a member? ×
  • advertisement_alt
  • advertisement_alt
  • advertisement_alt

Fretting a Bass


Jabba_the_gut
 Share

Recommended Posts

I'm getting close to installing frets in a bass I'm building and would like to know if I should glue the frets in.

I found mixed opinions from the web and I'm guessing this topic has been discussed on here at some point (though I couldn;t find a thread)

I've got two necks I'm going to do, one has a wenge board the other is maple if that makes any difference. These are also new fretboards that have not had frets installed before.

There seemed to be a fait bit of stuff on the web from using Titbond, superglue, epoxy resin or not using anything at all.

I'd be grateful for anyones opinion on this....

Cheers

Jez

Link to comment
Share on other sites

Hi Jez,
this will be scratch build #2 I presume?...............very nice job sir!
I have read about and used superglue, not sure how good Titbond(?) fnar fnar,(Titebond) or epoxy is, but like yourself I did a fair bit of reading up on it beforehand and ended up just as confused.
It seems everyone has their favourite method and they all seem to hold the frets in well enough.
I decided in my case that as it was my first fret job I would use superglue and do just a few frets at a time. It worked out quite well and the only thing I will do differently next time (and there WILL be a next time) is to try the pre-bent fretwire which comes ready cut.......I found it a right pain bending it to a consistent radius.
While I'm on, the build I'm just about to start on features a lot of wenge.......a wenge neck and fingerboard.....did you cut the fret slots on your neck yourself, if so how did it work out....any tips as I've read that wenge is quite splintery but worth the effort in the end

good luck with yours

Harry

Link to comment
Share on other sites

Ah...didn't spot that typo!!!

I bought the fretboard with the slots pre-cut for this one. Next time I think I will have a go at doing that myself to. I'm trying to learn a bit more with each one I build.

I'm kind of leaning towards using superglue to hold the frets so thanks for letting me know how you found it. Cheers also for the advice regarding pre-bend frets - that might save a bit of time.


Cheers

Jez

Link to comment
Share on other sites

I used a bit of 'no more nails' to refit an errant fret (for shame) and that's been fine so far - very messy though.
The best idea I've seen is to use contact adhesive and thinners, then use a craft knife to dribble it into the tiny gap between the fret and the board.

Tried that too - very fiddly but smells wonderful.

Link to comment
Share on other sites

If you're useing nickel-silver fretwire then you wanna over do the radius on the fret before fitting quite a lot so it's too curvey. Tap the ends of the fret into the slot first then work from middle outwards. This puts some sideways pressure on the tangs and frets hold better. With stainless frets you want the radius to be as per fretboard before tapping in.

I really cant see any reason to use superglue (or anything like that) to hold frets, it's just not necessary and it's only gonna make a mess and really screw things up years down the line when you need to take the frets out for a refret. If you get one fret that doesnt seat properly just whip it out, and stick a new over-bent one in rather than bodging it with glue.

Wenge does splinter really easy and you have to be very carefull when cutting across the grain

Edited by nugget
Link to comment
Share on other sites

[quote name='nugget' timestamp='1348077359' post='1809006']
If you're useing nickel-silver fretwire then you wanna over do the radius on the fret before fitting quite a lot so it's too curvey. Tap the ends of the fret into the slot first then work from middle outwards. This puts some sideways pressure on the tangs and frets hold better. With stainless frets you want the radius to be as per fretboard before tapping in.

I really cant see any reason to use superglue (or anything like that) to hold frets, it's just not necessary and it's only gonna make a mess and really screw things up years down the line when you need to take the frets out for a refret. If you get one fret that doesnt seat properly just whip it out, and stick a new over-bent one in rather than bodging it with glue.

Wenge does splinter really easy and you have to be very carefull when cutting across the grain
[/quote]

Cheers Nugget. How's your latest build going?

Link to comment
Share on other sites

[quote name='Jabba_the_gut' timestamp='1348079950' post='1809057']
Cheers Nugget. How's your latest build going?
[/quote]

:( It's been put away for a while, I've got a couple of other little projects to finish then I've got 2 builds to start for others so mine has to take a back seat....
I've just realised you're only just up the road from me, let me know if you ever need anything

Link to comment
Share on other sites

[quote name='Si600' timestamp='1348128471' post='1809560']
How are you cutting the fret slots? The only time I've done it the frets were sort of in the right place, but not quite.
[/quote]

I made a simple jig to cut the frets 100% square and vertical. It's basically just a sledge than runs on a straight edge (could be anything) and ends up with a perectly square front edge and a piece of flat mdf attached to the saw. Works amazingly well and only took a couple of hours to knock up. Mount the neck parallel to the straight edge. Can be used for a radius jig also without removing the neck so there is only one setup time


It looks a bit rough but works a treat
.[attachment=118867:DSC04131.JPG]
[attachment=118868:DSC04132.JPG]

Link to comment
Share on other sites

[quote name='nugget' timestamp='1348135853' post='1809719']
:( It's been put away for a while, I've got a couple of other little projects to finish then I've got 2 builds to start for others so mine has to take a back seat....
I've just realised you're only just up the road from me, let me know if you ever need anything
[/quote]

Cheers for that. Might give you a shout in the near future - be interested in seeing the basses you've made.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

 Share

  • Recently Browsing   0 members

    • No registered users viewing this page.
×
×
  • Create New...