Jump to content
Why become a member? ×

*edit*


dlloyd
 Share

Recommended Posts

Swap the 6L6's around - if the dimmer tube stays dim, replace it. If it's the socket that stays dim, take it to an amp tech. It's probably a failing resistor. Hum in an amp tends to mean the power supply is 'out of balance' - i.e. one of the tubes is mismatched some how. My guess is it's a failing tube.

Cheers

Link to comment
Share on other sites

You might get the right fuse at B&Q, but are more likely to get it from an Audio/Visual or guitar shop. Your twin might have an adjustable bias and if vibration has caused the bias to slip, it may be putting too much current through one of the 6L6's. Has the dimmer valve got any red patches on any of the internal metal plates?

What year and model is the Twin?

Hamster

Link to comment
Share on other sites

[quote name='dlloyd' post='61516' date='Sep 17 2007, 04:30 AM']The fuse that blew was a 12 amp glass bodied fuse.[/quote]
That doesn't seem right. The US version runs no more than a 6 ampere fuse at 110v. so a UK transformer version shouldn't use more than 3 amps at 220v. Blowing a 12 amp fuse at 220v indicates a dead short inside there somewhere. Powering it up again with that large a fuse could compound the damage.

Link to comment
Share on other sites

[quote name='dlloyd' post='62057' date='Sep 18 2007, 05:02 AM']The warning on the back of the amp specifies a 12 A 250V fuse.

I've taken the amp to the local guitar shop, where there's a good tech, to be looked at.

I think I'm going to start considering weight as a factor when I buy amps. Ouch.[/quote]
I just double checked my schematics file to be sure, the fuse for the Twin 1968-1982 was 2.5 amp/110v. That would make a UK version 1.25 amp at 220v. Reissue versions woudn't be siginificantly larger. A 12 amp/220v fuse is large enough for arc welding, and your shop should know that. Since they don't, and they can't fix it either, that would serve as notice that they should be avoided in the future. BTW, the hum is probably from power supply caps that are in need of replacement.

Link to comment
Share on other sites

[quote name='Bill Fitzmaurice' post='63127' date='Sep 20 2007, 02:57 PM']I just double checked my schematics file to be sure, the fuse for the Twin 1968-1982 was 2.5 amp/110v. That would make a UK version 1.25 amp at 220v. Reissue versions woudn't be siginificantly larger. A 12 amp/220v fuse is large enough for arc welding, and your shop should know that. Since they don't, and they can't fix it either, that would serve as notice that they should be avoided in the future. BTW, the hum is probably from power supply caps that are in need of replacement.[/quote]

I'm with Bill on this one. They don't know what they are doing. I have a Pro Tube Twin and that has a 2A fuse (main) and the internal fuse is a 5A fuse - off the top off my head. If it's the same Pro Tube Twin as I have got (the tremolo equipped two channel amp), the 5A internal fuse goes from time to time (I think it has gone twice in 3 years). If the internal fuse goes, you'll have to take the chassis out to replace it. It is in a fuse holder just off the main board. If this fuse goes, you'll see the tubes light, but you'll only get the heaters.

A cap change may well be in order as Bill says. If it hasn't been used for a while, the caps may have gone bad. They don't make 'em like they used to. These amps are quite hard on components... expect at least a set of tubes a year - most due to the fact that they are hanging upside down, inches away from a pair of speakers...

This amp shouldn't need sending back to Fender unless the boards are whacked. Any amp tech worth their salt should fix this in a jiffy.

PS - don't even think about doing anything yourself unless you know what you are doing. Fairly big caps inside that beast and they will give you heart a little bit of a tickle...

Link to comment
Share on other sites

[quote name='dlloyd' post='63339' date='Sep 20 2007, 09:57 PM']Why would anyone return a burnt out fuse to an amp after trying new tubes in it?[/quote]

a) because they are that tight they can't spare the fuse
:) they haven't touched the amp
c) they don't know what they are doing
d) all of the above

Link to comment
Share on other sites

  • 3 weeks later...
  • 2 months later...

[quote name='dlloyd' post='102503' date='Dec 11 2007, 12:31 AM']Anybody want to recommend an amp tech who is worth his salt?

The twin has had a lengthy holiday and is coming back unfixed. The problem indeed appears to be in the power supply, but for some reason the guy who has had it for a while has been unable to fix it.[/quote]

'fraid I can't help you up that neck of the woods? Anybody else want to give this chap a hand?

Link to comment
Share on other sites

Steve will fix it - [url="http://www.stevesamps.co.uk/"]http://www.stevesamps.co.uk/[/url] he's in Godalming Surrey though.

Steve also recommends this guy - [url="http://www.chambonino.com/"]http://www.chambonino.com/[/url] in Nottingham

Hamster

Link to comment
Share on other sites

I don't know if this is any help or of interest but I have a '94 twin which melted it's transformer.
After replacing a blown fuse at a rehearsal. I noticed a burning smell and looked in the back to see all power amp valves glowing like fluorescent tubes and black molten stuff dripping from the power transformer.
It was still under warranty so it went back to Fender (then arbiter in Cricklewood) via Coda music where I bought it who were extremely helpful in chasin Fender.
They replaced the transformer and valves. Apparently the transformer fitted in the US was only rated 220v and they upgraded it to 240v. it's been fine ever since.

I don't know whereabouts you are but you could try Panic Music near Cambridge. They aren't cheap so get an estimate.
you can find them via google I should think.

Edited by lonestar
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

 Share

  • Recently Browsing   0 members

    • No registered users viewing this page.
×
×
  • Create New...