Jump to content
Why become a member? ×
  • advertisement_alt
  • advertisement_alt
  • advertisement_alt

Freaky Fretless rebuild


6v6
 Share

Recommended Posts

Not exactly a build, more of a rebuild of a bass I acquired recently in a trade with a good friend who's had this bass for many years and it now needs some TLC.

Unsure of the exact maker of this, it says "The freaky guitar company" on the headstock, and the pickups date it to mid '80s - 1984 on the P pickup, 1986 on the bridge humbucker (which I assume was added as a retrofit based on the later pickup date, slightly wonky routing and lack of finish in the cavity).

It plays really nicely, sounds great, but the finish is pretty retro (Orange/Pink - very '80s!) and quite dinged up and cracked so my plan is to strip & refinish it, add a scratchplate, and possibly re-profile the pointy reverse headstock a bit.

Here's what I'm starting with:

Link to comment
Share on other sites

I decided to start with making a template for the pickguard, partly because it'll help figure out what needs to happen with the control cavity and holes, and partly because I got a shiny new router table I wanted to play with ;)

I've never used a router table before, so this was a bit of a learning process, but basically I made a template of the entire body in 6mm MDF (double sided taped to the body face down), then routed a rebate from this template onto another piece of MDF to get a consistent gap from the edge of the body to the pickguard edge.

Then I used a template I made recently for my precision to make the top edges of the templates, followed by a bit of sanding. Turned out OK I think.



Link to comment
Share on other sites

Thanks for the comments folks :)

So, I must admit have been a little torn over this, as yes it is a fun and unique colour combination, and I suppose it could become the Burgundy Mist of 2040 :lol: but ultimately I couldn't help it, I've attacked it with acetone, a heat gun and sandpaper to reveal this:



Kind of interesting, the centre splice looks like Ash (or possibly even oak?) with wings of what I'll call Mahogany but I'm not really sure.

Still some stripping to go, then lots of sanding followed by primer. Then decision time re the replacement colour (currently leaning towards the boring option of going with gloss black...)

Link to comment
Share on other sites

[quote name='Andyjr1515' timestamp='1473267480' post='3128545']
Much more likely to be ash than oak. In terms of the wings, is that a veneer on top? The edges look much lighter...
[/quote]

I think it's a trick of my dodgy photo, the wings are solid (I've stripped the back and most of the sides now)

Link to comment
Share on other sites

[quote name='6v6' timestamp='1473291060' post='3128859']
I think it's a trick of my dodgy photo, the wings are solid (I've stripped the back and most of the sides now)
[/quote]
In that case maybe mahogany (or similar species). If it's as heavy as hell, it might even be iroko?

Whatever - those look to be mighty fine woods. I reckon a clear/natural finish of some description should be there amongst your considered options...

Link to comment
Share on other sites

Thanks for the comments folks, definitely giving the natural finish option consideration now, just not sure how feasible it is given a few nicks on the body where filler/paint remain. More sanding to go before any final decision is made, but I'm still leaning towards a solid finish atm :)

I also need to sort out the control cavity cover and wonky bridge pickup routing before attempting any finishing, so I've started the control cavity today.

The process I used was to start with creating a control cavity cover template out of MDF. Then I spent a considerable amount of time drinking tea puzzling over how to get a matching template for the rebate into the body.

In the end I used a similar approach to an "inlay kit", which apparently is the professional name for two different guide bushings which combine to allow routing matching male/female templates. I happen to have a 10mm and 17mm guide bush on hand, so I combined these wiith 6mm and 3mm bits to route a template with 0.5mm oversize from the cavity to cover template. Not perfect yet, but with some sanding I think I can get both templates OK before routing the actual body/cover.





Link to comment
Share on other sites

  • 4 weeks later...

[quote name='rushbo' timestamp='1476634066' post='3155815']
Nice work - I'd be inclined to round off the lower horn of the pickguard, but you've got that three-ply thing down!
[/quote]

Thanks for the comment - yeah I agree the lower horn will probably see a little refinement with file/sandpaper before final fitment.

Link to comment
Share on other sites

[quote name='Andyjr1515' timestamp='1476900839' post='3158331']
Looks splendid. I'm attempting to make a pickguard shortly. I find them a right pain! Do you have any tips and tricks?
[/quote]

Well this is the first one I've attempted, but the approach I took was to make an mdf template, double stick tape the plastic to the template, then use a flush trim bit in the router table (got a cheap one from aldi!) followed by a chamfer bit to cut the bevel.

Worked pretty well but I had to experiment with the depth of cut on some scrap to get the bevel looking right.

I suspect the same approach would work with a hand held router, but I'd probably make a thicker template so it could be stuck securely to the bench without the bearing fouling, and possibly add a sacrificial thin mdf board on top to avoid marking the plastic with the router base.

There are some pretty good tutorials of the router table method on YouTube which is how I figured it out, good luck! :)

Link to comment
Share on other sites

[quote name='6v6' timestamp='1476944955' post='3158620']


Well this is the first one I've attempted, but the approach I took was to make an mdf template, double stick tape the plastic to the template, then use a flush trim bit in the router table (got a cheap one from aldi!) followed by a chamfer bit to cut the bevel.

Worked pretty well but I had to experiment with the depth of cut on some scrap to get the bevel looking right.

I suspect the same approach would work with a hand held router, but I'd probably make a thicker template so it could be stuck securely to the bench without the bearing fouling, and possibly add a sacrificial thin mdf board on top to avoid marking the plastic with the router base.

There are some pretty good tutorials of the router table method on YouTube which is how I figured it out, good luck! :)
[/quote]
In any terms, let alone a first try, I think that's a splendid job...

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

 Share

  • Recently Browsing   0 members

    • No registered users viewing this page.
×
×
  • Create New...