slazman Posted April 22, 2012 Share Posted April 22, 2012 Got my Fender Jaguar this week after a few weeks of searching for a nice pre-loved one - its in great condition but none the less I feel the need to give it a clean up. Any tips here - particularly cleaning the fretboard which has the pearloid block inlays. I would normally use Lemon Oil. Quote Link to comment Share on other sites More sharing options...
Doctor J Posted April 22, 2012 Share Posted April 22, 2012 Lemon oil will be just fine, i've used it on a blocked and bound fretboard before without any problems. Quote Link to comment Share on other sites More sharing options...
MikanHannille Posted April 22, 2012 Share Posted April 22, 2012 I use those cleaning/polishing wipes by EB with my 70's jazz. They work really well. Quote Link to comment Share on other sites More sharing options...
TRBboy Posted April 22, 2012 Share Posted April 22, 2012 Lem-oil for any fretboard (apart from maple!), and whenever I re-string these days I always give the frets a quick once over with Planet Waves Fret Polishing System. Really helps to keep the frets tip-top! If you've got any decent car polish kicking about, it should be fine for the paintwork too. Quote Link to comment Share on other sites More sharing options...
janmaat Posted April 22, 2012 Share Posted April 22, 2012 I have in the past cleand some seriously dirty and greasy guitars Keep in mind I am no pro restaurateur, but my experience was: for the real hefty greasy dirt (if there is) yes use soap + water and soft side of a sponge and elbow grease. I make sure though that the water would not sink into the wood so I always wipe it dry with lots of tissue straight after. When the dirt is gone, I re-moister the finger/fretboard using a nice oil from the local wind instrument shop that they use for recorders (they have a whole shelf ful of differnt oils there but it's pretty much a question of smell+taste, apart form the purity, of the oil). Not much oil needed, much better to do a little and wait a little and if needed, do it again. This method worked multiple times for me. Quote Link to comment Share on other sites More sharing options...
Gust0o Posted April 22, 2012 Share Posted April 22, 2012 [quote name='TRBboy' timestamp='1335081800' post='1625393'] Lem-oil for any fretboard (apart from maple!), and whenever I re-string these days I always give the frets a quick once over with Planet Waves Fret Polishing System. Really helps to keep the frets tip-top! If you've got any decent car polish kicking about, it should be fine for the paintwork too. [/quote] What are you using on maple, out of interest? Of course, in the long tradition of [i]ask three bass players, get five answers[/i], another player told me never to use Lemon Oil on Rosewood - instead, Linseed Oil should be used. Make of that what you will. I've used a combination of the following before: - Wire wool, to remove gunk (sweat residue, general dirt, decaying lacquer) - Cocktail sticks (to get in along the frets) - Fret polish (gotta have some bling) - A cleaning oil... be it Lemon, Linseed or other, as per your preferences Car polish can work, but be careful of abrasive polishes on some finishes. Mindst you, the Jaq will likely have a clear finish as the top coat, so it's probably just a case of wiping that and buffing to a shine, using a clear polish as appropriate. Quote Link to comment Share on other sites More sharing options...
TRBboy Posted April 22, 2012 Share Posted April 22, 2012 (edited) [quote name='Gust0o' timestamp='1335137250' post='1626334'] What are you using on maple, out of interest? Of course, in the long tradition of [i]ask three bass players, get five answers[/i], another player told me never to use Lemon Oil on Rosewood - instead, Linseed Oil should be used. Make of that what you will. I've used a combination of the following before: - Wire wool, to remove gunk (sweat residue, general dirt, decaying lacquer) - Cocktail sticks (to get in along the frets) - Fret polish (gotta have some bling) - A cleaning oil... be it Lemon, Linseed or other, as per your preferences Car polish can work, but be careful of abrasive polishes on some finishes. Mindst you, the Jaq will likely have a clear finish as the top coat, so it's probably just a case of wiping that and buffing to a shine, using a clear polish as appropriate. [/quote] You don't want to use anything much on maple if you can help it, except a clean dry cloth. If you've got some "gunk" of some sort on there, I'd try gently rubbing it with an alcohol wipe. You really don't want to use any type of oil because of it gets under the finish/laquer anywhere (usually where the frets are seated), it's a downward spiral. Apart from having marks/stains that you can't get rid of, it'll start to lift the finish. I really wouldn't use linseed oil, as it is thicker than lemon oil and will actually leave a shiny coating (almost like a fine varnish) on the fretboard, although maybe some folk like that. People use it on cricket bats! Apart from being good for cleaning the surface, Lem-oil is very, very thin, and is really there to penetrate into the fretboard and keep the wood moisturised and protected from your sweat, etc. Wouldn't wire wool be really abrade the finish!? On really gunky guitars, I've used either lem-oil or alcohol wipes (whichever is most appropriate) and a medium plectrum to get it off! Edited April 22, 2012 by TRBboy Quote Link to comment Share on other sites More sharing options...
Gust0o Posted April 23, 2012 Share Posted April 23, 2012 [quote name='TRBboy' timestamp='1335138225' post='1626344'] Wouldn't wire wool be really abrade the finish!? On really gunky guitars, I've used either lem-oil or alcohol wipes (whichever is most appropriate) and a medium plectrum to get it off! [/quote] No, not if you're sensible - if you're using it like sandpaper, then yes; you'll get out what you put in. A light scrub will simply remove the dirt. You'll find it's quite a common recommendation on this forum. I wish I had more before-and-after pictures to show you the difference it can make. Quote Link to comment Share on other sites More sharing options...
uncle psychosis Posted April 23, 2012 Share Posted April 23, 2012 [quote name='Gust0o' timestamp='1335171986' post='1626503'] No, not if you're sensible - if you're using it like sandpaper, then yes; you'll get out what you put in. A light scrub will simply remove the dirt. You'll find it's quite a common recommendation on this forum. I wish I had more before-and-after pictures to shour you the difference it can make. [/quote] I'd be happier using an old toothbrush instead of wire wool! Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.