Jaybeevee

Hi Bill, any chance you can flesh out this a little please. How does one maximise the decibels via cab selection/utilisation?

have you checked out Ian Allison on YouTube, he does some good walk throughs on this. But I will add I achieve what you're describing with the MXR.. word of warning though, It can be a bit tricky to dial in. It seems each of the controls affects the other, so you can end up chasing yourself around a little. But once set, it responds really well to your playing. You can get really good swell decay control from your plucking/picking hand. It's a bit sensitive to basses too, one setting doesn't fit all.

wow, never heard anything like that before. I can ask the question

Shucks, the point of my asking the initial question was just to help me understand something I haven't seen before. to try to figure out if I have an issue or not. I´m not sure naming the product is appropriate is all. I wouldn't like to suggest an issue that I am mistaken about (and it seems I am to some degree). The guys are really service minded and I don't want to betray that. It's no biggie, just being respectful

Thanks, yep.. when i posted the thread this is exactly what I was wrestling in my mind as this is what I was seeing. The builder didn't answer me dirctly on this point. I will ask him directly again. Wow, great info, really insightful. So am i understanding..? the driver input power in watts (same as the amp output power going into the speaker) varies considerably with regards to the frequency of the signal, the signal being volts. But what difference will a linear volume pot Vs a Log volume pot have on the user? based on my original query that volume at 11o'clock causing the amp to clip was both new and suspect to me? I was given the understanding that as a user, i can expect to set the master volume higher in it's range than i would normally expect to.. er go this is normal for this amp. Playing my Stingray wide open, with the pre amp (of the amp) set to it *crunch* position (on the gain dial) and the 6db drive button engaged (within the design intent of the pre-amp and without clipping at lower volumes) and then not getting past 11 o'clock on the master without clipping seemed like an issue, especially as it was (although quite loud) not loud enough to keep up a loud drummer.

I think in this case it does. it is apparently a different approach to that used in most amps. This is a point made by the builder leading me to understand that the pot position does relate to the power being delivered. Good idea, but I have returned it now. I wait and see what comes back This is knowledge above my pay grade, but in terms of the pot used on the master, the builder specifically talks about this aspect and that the power delivery from the amp is via a linear (not sure of the technical terms) pot, and the user can expect to run the master at a higher setting than would be normally expected.

Yeah, sure I could, but I was giving it a run. I wanted to test and hear various settings. I used the per-amp features in this case to get a nice not to dirty overdriven tone, and once found that, I wanted it loud enough to play with the drummer. The amp wouldn't deliver this without clipping. The high pass thing.. gawd knows..

Well I guess I was, where as i was using my Stingray 2 eq wide open. With respect to a 77 Stingray eq, they are bass treble cut n boost despite no centre indent. So yeah. It is how I always play it though and again I was A/B testing against my current amp (similar in power, solid state transformer etc). I didn't have a passive bass to hand to see if the clipping was occurring at similar levels. And here is another thing. This particular amp is made or fitted with linear pots. Where as most amps deliver more power in the early part of the volume sweep, and much less in the later, this amp delivers a linear power based on the pot adjustment. As mine was clipping at 11 (o'clock) this is less than half the full power. In any case, the builder thinks it may have taken a knock in transit. So i´m hoping that is the case. There is not Active/passive input switch, and so I hoping there isn't an inherent problem with this amps suitability to active basses. I have actually read a comment by an active player who had similar issues with this amp, so we see when I get a replacement.. Thanks for the input.

It's a new build from a small manufacturer. To be honest I´m not comfortable with saying what manufacture as it may not be a fault or I maybe misrepresenting something. I was really only trying to understand if master volume affecting clipping was a thing as I was sitting mulling it over and thought a quick post here might enlighten me. I got an answer to that early in the thread. The manufacturer is supporting me, so I see what's what after I get a replacement. Cheers though

Never thought of that. In my case same cables between both amps, but its a good bit of wisdom. Thanks

2 8ohm 112s, TKS 1126s to be precise. Amp is 400w @ 4ohms. My Main Amp is 500w @4ohms and is thunderous

Thanks, that's something new for me. Unfortunately, not supplied with a manual, and the manufacturer is not answering me specifically on this point.

A bit loosely described. I had the gain at about 2óclock to where the amp identifies ´crunch´. The amp also has a drive button providing 6db more to the tubes. With my Stingray I was getting some nicely mild overdriven tones.. point being well within the design intent of the amp. Then I tried to up the master to match the drummer. So I´m expecting all to be good. The master was set at around 11 clock when the clip light and distorted signal break up occurred. Again, if it's not hitting rehearsal volumes at these settings I´m suspecting an issue with the amp. I was just looking to get confirmation of that or some learning. 400W Mos Fet Transformer power supply should easily handle what I was asking of it. I was just wondering if clipping from the master is expected or un expected.

Cabs are good for the amp. In terms of Watts the amp is's delivering towards the lower of the recommended range, and I run a more powerful amp at higher volumes. It was a circuit/electrical kind of distortion sound. hard to describe, but it sounded like the amp was at fault. I just never seen or realised clipping could be produced from master volume control. I will add that in terms of settings, the amp should have coped I feel.

Hi Folks, I recently picked up an amp (hybrid) class A/B that clipped when I cranked the master volume. Should that happen? I was pushing the (tube) pre amp a bit, and then to get it up to loud drummer volume, I up´t the volume to 12 o'clock and was getting clipping light flashing with a horrid distortion which accompanied the clipping light. Sounded like the cab was farting. I always thought (assumed) clipping was associated to the pre amp. Is it normal or knackered? Cheers

Soon a member of the club. My R400 is winging it's way to Norway as we speak..

Around 650 Euros is what I was quoted..

One of em has My name on it 👏

The Handbox R400 will fit the Bill. There is a 30 Odd page thread on here. A fav of Andy Irvine, so loads of YouTube stuff to go at too.

Jeez for hand crafted boxes... this must be really labor intensive and costly.. Have to say, it doesn't seem reflected in the price..

When they finally become available I can see me being still really tempted even if i am loving the Thunderfunk..