Jump to content
Why become a member? ×

JensWest

Member
 View Profile  See their activity

  • Posts

    168

  • Joined

  • Last visited

 Content Type 

Everything posted by JensWest

  1. JensWest
    On hold!
  2. JensWest
    bump
  3. JensWest
    It sure is. Thank you.
  4. JensWest
    bump
  5. JensWest
    [quote name='blunderthumbs' timestamp='1393337038' post='2378889'] Hi. Have you tried putting this on the Statii website "Basses for sale" Section I notice it's been on here for some time. I'm sure you'd get some interest on Statii. [/quote] Hi. Yes, I have. But thank you for the tip.
  6. JensWest
    bump
  7. JensWest
    bump
  8. JensWest
    [quote name='bassman7755' timestamp='1392820958' post='2373089'] The marshall DB series (at least my old 7200 was) are 4ohm minimum total load AFAIK so you cannot connect 2 4ohm speakers at the same time. [/quote] Even if the manual says you can...? [url="http://www.docstoc.com/docs/20390605/Dynamic-Bass-System---DBS-7400"]http://www.docstoc.c...stem---DBS-7400[/url] It sais so in the back of the head too, as stated in the first post.
  9. JensWest
    OK, great. Thank you!
  10. JensWest
    [quote name='Musky' timestamp='1392768956' post='2372650'] If both cabs are the same then using two 4 ohms cabs will be about 5dB louder - 3dB from the extra speaker and about 2dB from a typical 50% increase in power by running at half the impedance. Edit: You'll get an improved LF output as well. [/quote] Thank you for your answer, Musky! But, will the amp deliver 400 W at 4 or 2 Ohm?
  11. JensWest
    Hi all! In the back of it, it says: "Minimum load 2 Ohm (400 W R.M.S.)". There are two outputs and they each need a minimum load of 4 Ohm. Now, how much effect do I get if I connect it to two cabs á 4 Ohm and how much do it get if I connect one 4 Ohm cab? Thank you!
  12. JensWest
    bump
  13. JensWest
    New price!
  14. JensWest
    bump
  15. JensWest
    Replied!
  16. JensWest
    bump
  17. JensWest
    bump
  18. JensWest
    I think it looks really great (with some reservation for the lower horn)! Hope I'll get the chance to try one out some day and then see what happens...
  19. JensWest
    If you're lucky, it's still here when you're ready. Thank you. It looks even better in real life.
  20. JensWest
    Hi! Up for sale is my Status S2 Classic 6 NT. It could almost pass as new, if it wasn't for some wear to the neck pickup. I.e., it's in really, really good condition. The body is in mahogany, with a walnut tone-block and quilted maple facings. It has a graphite through-neck, with 24 frets and a phenolic fingerboard. The preamp (18 V) has a 3-band eq., with parametric pot. and toggle switch (cut/neutral/boost) for the mids (it also has both cut and boost for bass and treble), master vol. and blend. It's equipped with Status (Hyperactive) soap-bar pickups. It comes in the original Status (Hiscox) hardcase, also in good condition. The bass is located in Uppsala, Sweden, but can be shipped world wide. Send me a PM if you have any questions. More photos are available on demand. Thank you for your interest!
  21. JensWest
    OK. Thank you.
  22. JensWest
    Damn... OK. How is the ramp attached?
  23. JensWest
    OK. So the frets were only cleaned, not leveled and crowned?
  24. JensWest
    What was done during the refin?
  25. JensWest
    [quote name='Kiwi' timestamp='1390894313' post='2350878'] Looks like an EG rather than GN with that extra laminate in the body wings. [/quote] A GN can have an extra layer of laminate. Which are the letters in the serial, tomika?
×
×
  • Create New...