AxelF Posted September 1, 2009 Share Posted September 1, 2009 I've just changed the strings on a P bass I have, and switched to flats (it's used solely for Motown) and a heavier gauge. It sounds fantastic, apart from the open A string, which now buzzes against the first fret. It's absolutely fine from the Bb upwards, and I'm fairly sure I can see/hear it hitting the first fret so I'm almost certain it's the first fret that's the problem. I'm guessing that it's the heavier gauge causing the issue - I've tried raising the action with no success, what can I do to solve the problem? Is it a case of needing a new nut? Thanks in advance... Axel Quote Link to comment Share on other sites More sharing options...
geoffbyrne Posted September 1, 2009 Share Posted September 1, 2009 Could be the nut slot cut too low. Try slipping a little bit of paper between the nut & the string. If this works, you can build up the slot using baking soda & super glue (careful - it gets hot!!!) which sets pretty hard & can be re-cut. G. Quote Link to comment Share on other sites More sharing options...
Al Heeley Posted September 1, 2009 Share Posted September 1, 2009 Yep - simply a small folded piece of silver foil carefully inserted between string and nut can give that extra few tenths of a mm height gain to stop fret buzzing. Being particularly lazy with one of my basses, this temporary measure seems to have happily lasted 2 years now. Quote Link to comment Share on other sites More sharing options...
The Bass Doc Posted September 1, 2009 Share Posted September 1, 2009 A buzz on the open string can also indicate insufficient wrap around the post leaving the string to vibrate behind the nut - try holding it down between nut and post while you strike the open note and if this makes the buzz disappear your answer is to re-string leaving more wraps around the post or you may get away with simply holding the wrap-around low enough during re-tightening of the existing string. Quote Link to comment Share on other sites More sharing options...
AxelF Posted September 1, 2009 Author Share Posted September 1, 2009 Thanks for the replies guys, have to put my hands up here and admit to the old operator error.... Hadn't wound the string round the post properly when restringing, and slackening and redoing it properly seems to have cured the problem. Thanks for the baking soda and superglue trick though, never heard of that so I've learned two new things today! Thanks again, Axel Quote Link to comment Share on other sites More sharing options...
Al Heeley Posted September 2, 2009 Share Posted September 2, 2009 That'a a Dan Erlwine special (http://www.amazon.co.uk/Guitar-Player-Repair-Guide-Electrics/dp/0879302917/ref=sr_1_3?ie=UTF8&s=books&qid=1251887646&sr=1-3 )essential book for anyone interrested in set up and maintainence of their own instrument. Quote Link to comment Share on other sites More sharing options...
mrcrow Posted September 2, 2009 Share Posted September 2, 2009 [quote name='AxelF' post='587079' date='Sep 2 2009, 12:36 AM']Thanks for the replies guys, have to put my hands up here and admit to the old operator error.... Hadn't wound the string round the post properly when restringing, and slackening and redoing it properly seems to have cured the problem. Thanks for the baking soda and superglue trick though, never heard of that so I've learned two new things today! Thanks again, Axel[/quote] i have always throught an A washer was in order on fenders Quote Link to comment Share on other sites More sharing options...
Al Heeley Posted September 4, 2009 Share Posted September 4, 2009 Isn't that one of the common criticisms of P's and J's, that due to the lack of pressure on the A-string going over the nut, that the A sometimes rattled or lost definition? I always try to wind on a bit more on the A, and force the windings downward so the final wrap sits at the bottom, next to the headstock, so the break-angle can be maximised. Some of those fluted or conical machine head winders might be useful there to help keep the string windings nestled at the base of the shaft. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.