Jump to content
Why become a member? ×
  • advertisement_alt
  • advertisement_alt
  • advertisement_alt

Trace Elliot VA400 Help


ValleyArts
 Share

Recommended Posts

Hi everyone I have a VA400, when I engage the pre shape or graphic button it makes a weird short hum, it's hard to explain, and the hum also kicks in when you slap. I've attached 2 videos to show what I mean.

 

Hopefully someone knows what the problem is I would like to use the amp as it sounds great but those noises and the hum coming from the amp makes it almost unusable.

Link to comment
Share on other sites

Is the short hum present when using both the valve pre-amp input ( RED ) and the standard pre-amp input ( GREEN ) or does the symptom change when using either input with the shape/graphic buttons? Also are you using the front buttons or a footswitch to activate the shape/graphic?

Link to comment
Share on other sites

8 hours ago, DGBass said:

Is the short hum present when using both the valve pre-amp input ( RED ) and the standard pre-amp input ( GREEN ) or does the symptom change when using either input with the shape/graphic buttons? Also are you using the front buttons or a footswitch to activate the shape/graphic?

Hi, the short hum from activating the buttons is coming from the green channel, but if I use both channels together it happens. Also I'm using the buttons to activate them not a footswitch :) 

Link to comment
Share on other sites

That sort of rules out the tube input and a potentially worn tube as that part sits in front of the green channel. Series 6 GP12 pre-amps are pretty solid and most things i've come across with them are usually age/wear issues with stuff like input jack contacts/ dry solder joints on the front board or occasionally some components failures after a long time. These amps are getting on for thirty years old so a few issues are to be expected. The graphic/pre-shape circuit is solid state switching, a couple of transistors and IC chips. Later SMX heads went back to physical relays instead of ICs. Each have good points and bad points for reliability. It could be just worn buttons or a dodgy transistor in the switching circuit but to be honest without getting the amp up on a bench to test, its just guess work. A VA400 is definitely an amp worth repairing so unless its been in and out of a tech shop costing you tons of money to keep it going, I'd keep it and see if you can find a local tech to check it over for you. Some folks on this forum have mentioned Ashdown might look at a Trace Elliot repair and if your in Essex, Heybridge might not be too far to travel and get your VA400 checked out by them. Worth a phone call I would say. 🙂

For the record, I haven't come across buzzing from the pre-shape/graphic on a Series 6 GP12 other than the actual press in switches being worn out. That usually just causes issues actually switching on/off not random hum noises. 

 

  • Thanks 1
Link to comment
Share on other sites

In general electromechanical components, switches, relays and even Jack sockets are less reliable than pure electronic devices like transistors an electronic switches. thirty year old relays, switches and jacks may well have reached the end of their lives, but are replaceable. 
 

  • Thanks 1
Link to comment
Share on other sites

On 07/05/2023 at 13:20, DGBass said:

That sort of rules out the tube input and a potentially worn tube as that part sits in front of the green channel. Series 6 GP12 pre-amps are pretty solid and most things i've come across with them are usually age/wear issues with stuff like input jack contacts/ dry solder joints on the front board or occasionally some components failures after a long time. These amps are getting on for thirty years old so a few issues are to be expected. The graphic/pre-shape circuit is solid state switching, a couple of transistors and IC chips. Later SMX heads went back to physical relays instead of ICs. Each have good points and bad points for reliability. It could be just worn buttons or a dodgy transistor in the switching circuit but to be honest without getting the amp up on a bench to test, its just guess work. A VA400 is definitely an amp worth repairing so unless its been in and out of a tech shop costing you tons of money to keep it going, I'd keep it and see if you can find a local tech to check it over for you. Some folks on this forum have mentioned Ashdown might look at a Trace Elliot repair and if your in Essex, Heybridge might not be too far to travel and get your VA400 checked out by them. Worth a phone call I would say. 🙂

For the record, I haven't come across buzzing from the pre-shape/graphic on a Series 6 GP12 other than the actual press in switches being worn out. That usually just causes issues actually switching on/off not random hum noises. 

 

Going to run it down to Ashdown today 😁

Edited by ValleyArts
  • Like 1
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

 Share

  • Recently Browsing   0 members

    • No registered users viewing this page.
×
×
  • Create New...