AngelLaHash Posted November 23, 2013 Share Posted November 23, 2013 I'm not sure where to start, so I'll just type what i am thinking to a degree. The Volume pot is being used as a [size=3][font=opendyslexic]potential [/font][/size]Divider, Input one side, middle the Output and other side is GROUND. So that what Voltage is made from the Pickups, from the strings pulling the Magnets via a Copper coil. As far as I know that the voltage out of these things is dam small And its not AC to speak of but a frequence range, normally 0-6KHz i think i read some were, but human hearing is 0-20KHz These are just things I've read Online (so not 100% the Truth) Is divided between the Two half's of the POT. So why 250K, why not 50K or like I'm told a good value for Humbuckle Picks up's is 500K. I know Electronics and Electrical's but i dont normally use a Pickup as a Power Supplie or do circuits with a "AC" circuits. Quote Link to comment Share on other sites More sharing options...
dincz Posted November 24, 2013 Share Posted November 24, 2013 The pickup and pot also form a voltage divider. The pot is purely resistive so its value is the same at any frequency. The pickup also has a fixed resistance but it's also inductive, so you have to add in its impedance (or AC resistance), which increases with frequency. If you use a low value pot, e.g. 50K, it may be fine for low frequencies but at high frequencies the pot's resistance is low relative to the impedance of the pickup and only a small proportion of the pickup's voltage will appear across the pot. It's effectively a frequency-dependent voltage divider so the pot's resistance must be high compared to the pickup impedance so as to maintain consistent level across the frequency range. Quote Link to comment Share on other sites More sharing options...
AngelLaHash Posted November 24, 2013 Author Share Posted November 24, 2013 (edited) First off, thanks you for explainging the bigger picture to me Dincz So what about the Bleed cap that is put in, People use 1nF, 1nF with a Resister (220K-120K) and 200pF That chances the Freq and the Impedance Xc=1/(2*Pi*C*f) Would it be best to have some Calculation to balance between the Pickups and the Volume pot Edited November 24, 2013 by AngelLaHash Quote Link to comment Share on other sites More sharing options...
dincz Posted November 24, 2013 Share Posted November 24, 2013 If you knew the inductance of the pickup winding, you could calculate a suitable value for the tone cap, but it's probably easier just to use the bass/pickup manufacturer's recommended value. Quote Link to comment Share on other sites More sharing options...
AngelLaHash Posted November 24, 2013 Author Share Posted November 24, 2013 Well Ive got a Induction Meter.. i would like to learn how you figure out what would be Best than what Suits and is ABOUT ok for the pickup Man trys for Perfection, and sadly falls a lot of the time Quote Link to comment Share on other sites More sharing options...
dincz Posted November 24, 2013 Share Posted November 24, 2013 Perfection is going to be different for every pair of ears. It really depends on how much of the top end you want to roll off, and by how much. The most accurate method would be to try a range of capacitance values and see how they sound. Quote Link to comment Share on other sites More sharing options...
AngelLaHash Posted November 24, 2013 Author Share Posted November 24, 2013 My current set up for my P-Bass is 2xHex Switching giving me a Range of 200pF to 100nF in 200pF steps thats just the tone contol's it also has [url="http://www.impossibleband.com/projets-electroniques/megatone/megatone---archive#TOC-Megatone-36"]http://www.impossibleband.com/projets-electroniques/megatone/megatone---archive#TOC-Megatone-36[/url] sort of like that but, i have more a range on the Caps and the "Boost" Resister has more 4 ranges 15k, 150K and 1K5 and direct to ground. So i just need to play around with them to find my area of perfection Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.