JensWest
-
Posts
168 -
Joined
-
Last visited
Content Type
Profiles
Forums
Events
Shop
Articles
Posts posted by JensWest
-
-
-
[quote name='blunderthumbs' timestamp='1393337038' post='2378889']
Hi. Have you tried putting this on the Statii website "Basses for sale" Section
I notice it's been on here for some time. I'm sure you'd get some interest on Statii.
[/quote]
Hi.
Yes, I have. But thank you for the tip. -
-
-
[quote name='bassman7755' timestamp='1392820958' post='2373089']
The marshall DB series (at least my old 7200 was) are 4ohm minimum total load AFAIK so you cannot connect 2 4ohm speakers at the same time.
[/quote]
Even if the manual says you can...?
[url="http://www.docstoc.com/docs/20390605/Dynamic-Bass-System---DBS-7400"]http://www.docstoc.c...stem---DBS-7400[/url]
It sais so in the back of the head too, as stated in the first post. -
OK, great.
Thank you! -
[quote name='Musky' timestamp='1392768956' post='2372650']
If both cabs are the same then using two 4 ohms cabs will be about 5dB louder - 3dB from the extra speaker and about 2dB from a typical 50% increase in power by running at half the impedance.
Edit: You'll get an improved LF output as well.
[/quote]
Thank you for your answer, Musky!
But, will the amp deliver 400 W at 4 or 2 Ohm? -
Hi all!
In the back of it, it says:
"Minimum load 2 Ohm
(400 W R.M.S.)".
There are two outputs and they each need a minimum load of 4 Ohm.
Now, how much effect do I get if I connect it to two cabs á 4 Ohm and how much do it get if I connect one 4 Ohm cab?
Thank you! -
-
New price!
-
-
Replied!
-
-
-
I think it looks really great (with some reservation for the lower horn)!
Hope I'll get the chance to try one out some day and then see what happens... -
If you're lucky, it's still here when you're ready.
Thank you. It looks even better in real life. -
Hi!
Up for sale is my Status S2 Classic 6 NT.
It could almost pass as new, if it wasn't for some wear to the neck pickup.
I.e., it's in really, really good condition.
The body is in mahogany, with a walnut tone-block and quilted maple facings.
It has a graphite through-neck, with 24 frets and a phenolic fingerboard.
The preamp (18 V) has a 3-band eq., with parametric pot. and toggle switch (cut/neutral/boost) for the mids (it also has both cut and boost for bass and treble), master vol. and blend.
It's equipped with Status (Hyperactive) soap-bar pickups.
It comes in the original Status (Hiscox) hardcase, also in good condition.
The bass is located in Uppsala, Sweden, but can be shipped world wide.
Send me a PM if you have any questions.
More photos are available on demand.
Thank you for your interest! -
OK.
Thank you. -
Damn... OK.
How is the ramp attached? -
OK.
So the frets were only cleaned, not leveled and crowned? -
What was done during the refin?
-
[quote name='Kiwi' timestamp='1390894313' post='2350878']
Looks like an EG rather than GN with that extra laminate in the body wings.
[/quote]
A GN can have an extra layer of laminate.
Which are the letters in the serial, tomika? -
A while back, I had a Sr3006E as my main bass and these are truly great!
Have a bump! -
Yes, that I've noticed.
Status S2 Classic 6 NT [SOLD]
in Basses For Sale
Posted
It sure is.
Thank you.