Jump to content
Why become a member? ×

3 Way Switch - Single, Series, Parallel - Wiring Help Please


bagsieblue
 Share

Recommended Posts

Looking for some help on replacing a 3 Way Switch as - Single, Series, Parallel.

I'm replacing a dodgy switch on a Warwick Doublebuck.

Drawing is here:

I've had to replace the 2 x PCB mounted switches (shown below as the switch module) with 2 x  individual switches, but have wired following the drawing below.

All works OK and is sounding great  - apart from I only appear to have 2 settings per switch/pickup rather than 3.

Position 1 single coil is fine.

Position 2 is a humbucker mode variation

Position 3 is humbucker mode variation

I hear no difference between position 2 and 3.  This is the same on both pickups so I'm assuming I've got something wrong somewhere.   Looking for input on what I need to do to get to the differing series and parallel settings.

Looking at the drawing - do I need a jumper wire between the top right and middle left positions?.

I assumed the switch covered that? or do I need to wire in a wire?

I've tried placing a wire between those two positions but that doesnt seem to change the sound either?

$$ diagram.png

Edited by bagsieblue
Link to comment
Share on other sites

Diagram here   - admittedly this is the Rockbass.

It's curious on this that the picked wires are coloured differently?

Even on the full wiring diagram different colour wires from the neck and bridge pickup go to different positions on the switch!!

rusty.png

Link to comment
Share on other sites

2 hours ago, bagsieblue said:

Looking for some help on replacing a 3 Way Switch as - Single, Series, Parallel.

I'm replacing a dodgy switch on a Warwick Doublebuck.

Drawing is here:

I've had to replace the 2 x PCB mounted switches (shown below as the switch module) with 2 x  individual switches, but have wired following the drawing below.

All works OK and is sounding great  - apart from I only appear to have 2 settings per switch/pickup rather than 3.

Position 1 single coil is fine.

Position 2 is a humbucker mode variation

Position 3 is humbucker mode variation

I hear no difference between position 2 and 3.  This is the same on both pickups so I'm assuming I've got something wrong somewhere.   Looking for input on what I need to do to get to the differing series and parallel settings.

Looking at the drawing - do I need a jumper wire between the top right and middle left positions?.

I assumed the switch covered that? or do I need to wire in a wire?

I've tried placing a wire between those two positions but that doesnt seem to change the sound either?

1 hour ago, bagsieblue said:

Diagram here   - admittedly this is the Rockbass.

It's curious on this that the picked wires are coloured differently?

Even on the full wiring diagram different colour wires from the neck and bridge pickup go to different positions on the switch!!

rusty.png

I think that would make sense if the single coils need to be phase reversed to give you a scooped mids sound.

David

Link to comment
Share on other sites

1 hour ago, bagsieblue said:

Diagram here   - admittedly this is the Rockbass.

It's curious on this that the picked wires are coloured differently?

Even on the full wiring diagram different colour wires from the neck and bridge pickup go to different positions on the switch!!

rusty.png

The switches are not symetrical in their operation -

Toggle position vs contact position:
P1 • 2-3, 5-6: ON
P2 • 2-1, 5-6: ON
P3 • 2-1, 5-4: ON 

If you have the switch wired upside down, then it will not switch the way the original did.

That might be worth checking.

David

Link to comment
Share on other sites

50 minutes ago, Mottlefeeder said:

The switches are not symetrical in their operation -

Toggle position vs contact position:
P1 • 2-3, 5-6: ON
P2 • 2-1, 5-6: ON
P3 • 2-1, 5-4: ON 

If you have the switch wired upside down, then it will not switch the way the original did.

That might be worth checking.

David

Thanks for that - I'm sure the switches arent wired upside down.

To be sure - I have the notch in the thread on the bottom or the underside, facing downwards  - is that right?

Edited by bagsieblue
Link to comment
Share on other sites

38 minutes ago, bagsieblue said:

.....and this is a photo of the board with the switches that I removed.

Same orientation it looks to me - I'm puzzled....

IMG_20210329_093815.jpg

I can't tell from the photo whether it is notch up or notch down, but I also can't confirm that any two switch manufacturers do it the same way, so the only way to check it would be with a multimeter, or a battery, bulb and length of wire. 

You need to check whether 'switch in central position' connects the centre and upper contacts or centre and lower contacts in the original switches and then check that you have done the same.

David

 

  • Thanks 1
Link to comment
Share on other sites

Ok, it's the correct switch.

Don't worry about the notch on the switch as you can turn it to the desired position afterwards.

There are 6 pins on your switch when you look at it from the rear.

Let's number them beginning on the top left and going to the bottom right, so you have 1 on the top left, 2 on the top right, 3 on the middle left, 4 on the middle right, 5 on the bottom left and 6 on the bottom right. 

1. Make a strap between 2 and 3 on both switches.

2. Starting with the neck pickup.

3. White on 2.

4. Red on 4.

5. Black on 6 = Output.

6. Green on Ground.

7. Ground on 5 too.

8. Now the bridge pickup.

9. Green on 2.

10. Black on 4.

11. Red on 6 = Output.

12. White on Ground.

13. Ground on 5 too.

This now should work.

Link to comment
Share on other sites

18 minutes ago, Hellzero said:

Ok, it's the correct switch.

Don't worry about the notch on the switch as you can turn it to the desired position afterwards.

There are 6 pins on your switch when you look at it from the rear.

Let's number them beginning on the top left and going to the bottom right, so you have 1 on the top left, 2 on the top right, 3 on the middle left, 4 on the middle right, 5 on the bottom left and 6 on the bottom right. 

1. Make a strap between 2 and 3 on both switches.

2. Starting with the neck pickup.

3. White on 2.

4. Red on 4.

5. Black on 6 = Output.

6. Green on Ground.

7. Ground on 5 too.

8. Now the bridge pickup.

9. Green on 2.

10. Black on 4.

11. Red on 6 = Output.

12. White on Ground.

13. Ground on 5 too.

This now should work.

Thanks  - that's the set up that I have, apart from a jumper wire between 2 and 3.  I've held a wire in place and changed the switch and there is no difference with the jumper wire in place.

Maybe the switch is upside down......

Link to comment
Share on other sites

If your switch is a DPDT On-On-On, there is no up or down position as it's internally wired the same way, so except for the notch, there's no upside down position.

Did you ground the pin 5 and the green (or white) wire ?

Link to comment
Share on other sites

13 minutes ago, Hellzero said:

If your switch is a DPDT On-On-On, there is no up or down position as it's internally wired the same way, so except for the notch, there's no upside down position.

Did you ground the pin 5 and the green (or white) wire ?

Thanks for the input - yes, did do.

All looks fine, sounds fine too - I'm just not hearing any difference between switch positions 2 and 3 (centre and facing down)

Link to comment
Share on other sites

21 minutes ago, Hellzero said:

If your switch is a DPDT On-On-On, there is no up or down position as it's internally wired the same way, so except for the notch, there's no upside down position...

I disagree. The supplier's connection table in my second post above shows that when the switch is in the central position, both poles connect to the same end, but with the switch not central, the two poles switch to opposite ends. If you turn the switch through 180 degrees your centre position will connect to a different set of contacts, so orientation is important.

David

Link to comment
Share on other sites

2 minutes ago, Mottlefeeder said:

I disagree. The supplier's connection table in my second post above shows that when the switch is in the central position, both poles connect to the same end, but with the switch not central, the two poles switch to opposite ends. If you turn the switch through 180 degrees your centre position will connect to a different set of contacts, so orientation is important.

David

5410faed57ea6bc1651393f937524ebcc8525244

Tell me where is the difference upside down, please ?

  • Like 1
Link to comment
Share on other sites

34 minutes ago, Hellzero said:

5410faed57ea6bc1651393f937524ebcc8525244

Tell me where is the difference upside down, please ?

You are right - there isn't a difference. The diagram I have shows the contact numbering going down on one pole and up on the other, like an integrated circuit. That numbering does give you a difference,  but it looks like it is wrong. One lives and learns.

David

Link to comment
Share on other sites

12 minutes ago, Hellzero said:

@bagsieblue Does it work now ? That said the difference between the single coil and parallel mode can sometimes be very hard to hear, but come close to a screen or a transformer and you'll instantly know which one is engaged. 😉

Thanks for checking back - I'll try again when I have more time.

I havent put a link in between, I will do this but I've held a wire in place and flicked the switch and nothing appears to change with that.

I'll try going close to a screen too and see if that helps identify.

Here is the bass.....

IMG_20210325_110016.jpg

Edited by bagsieblue
Link to comment
Share on other sites

On 30/03/2021 at 11:25, bagsieblue said:

I will do this but I've held a wire in place and flicked the switch and nothing appears to change with that

 

On 30/03/2021 at 11:53, Hellzero said:

You have to solder that jumper, otherwise it won't work the way it is supposed to do.

@Hellzero is absolutely right about this, @bagsieblue.  Holding a wire against a contact just doesn't cut the mustard with bass and guitar electrics.  I know, because I've tried that myself in the past ;)

It is also correct that the contacts 2-3 bridge is essential and that on the original circuit board this will be happening within the board.

It should be a 2 min job to solder the contact bridge, @bagsieblue .  If not already done, it's worth doing it because I'm pretty sure that, all else being correct to @Hellzero 's description, it should work.

The series /parallel switch, by the way, often doesn't produce a huge amount of a tonal difference, but you should hear a volume difference through an amp or see it through a DAW wave-form.

In terms of split coil, tapping the poles lightly with a steel screwdriver or similar when the bass is plugged in should tell you which rows of poles are connected and which are shorted out. 

Edited by Andyjr1515
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

 Share

  • Recently Browsing   0 members

    • No registered users viewing this page.
×
×
  • Create New...