Jump to content
Why become a member? ×

Finished Pics! Swift Lite 2 (sorry, another electric)


Andyjr1515

Recommended Posts

Yes - I know this might result in removal of epaulettes (or worse) but trust me, it'll be worth it because one day - I promise - I'll build some of the same design features into a bass!
 
This project is still in early stages at the moment, but is planned as an evolution of the recently completed 'Swift Lite' below

8aF0Uqjl.jpg

It's a commission from my brother-in-law's partner, Jane.  Female and new to guitar, Jane ticks two of the boxes of the type of players I had in mind when I was designing this.  Players who might appreciate a guitar that sounds good and looks good but doesn't weigh the equivalent of a sack of coal 
9_9 .  Those types of players include: young players; learners; old players; female players; anyone else who has asked the question 'So tell me again...just WHY are guitars so heavy?'

Will it be a copy?

No

But it will be an evolution sharing many of the same design features.  This is what I have in mind (actually, with one more tweak to incorporate):
1RAvzYBl.jpg

Some of the changes, which to be honest are using this new build as a test bed, are simply incorporating my own thoughts and feedback from regular players who've borrowed my own Swift Lite to try out and are just about playability for a lead guitar player.  This includes the slightly further back cutaways to allow a full thumb anchor at the top cutaway and full access to bend at the 22nd frets of the lower cutaway.  Yes - I know...there are other places they could put their thumb
xD:
ioynbuJl.jpg

The other change you can see is that the top horn is longer. 

My own Swift Lite balances perfectly on the strap - but at 5lbs 14oz is still a touch heavier than planned.  The new one is aiming for the original target of 5lbs 8oz max.  My logic is that, if mine balances just right, then any lighter might send it out of balance.  With the top strap button at the 12th fret, this will balance however light the body ends up.

Oh..and this might have some oak in it.

Yes - I know....madness on so many levels

More details as I crystallise them

Andy
 
Edited by Andyjr1515
Link to comment
Share on other sites

1 hour ago, Jimothey said:

So I’m intrigued by this build that you want it lighter but your going to include some oak?? O.o

I know - madness!

But the oak was a feature shelf that used to be over a large fireplace in the house she grew up in and which her parents lived in all their married lives.  So, even with all the reservations about it as a building wood, I'm going to incorporate some in the build.  Ideally, it would replace the sapele back - but that might make achieving the weight target impossible.  As you know, @Jimothey, from your own builds, it's all about compromises (and trigonometry ;) )

Link to comment
Share on other sites

I hope this doesn't become a "design by committee" but here's my 2p worth.

As Andy knows I was very pedantic about how the lines flowed in my Psilos. I've made a few amendments to Andy's design which, I believe, help the lines flow. This includes moving the lower cut back 1 fret.

Note how the bottom horn flows more into both the top horn and into the armpit cut which makes it easier on the eye. By adjusting where the top cut is made you can make the eye flow more pleasing (IMO).

What do others think??

5a7f524496656_andysguitar.png.acb228249de20dc05b57cf9740cee96d.png

Edited by TheGreek
Link to comment
Share on other sites

6 hours ago, Andyjr1515 said:
Yes - I know this might result in removal of epaulettes (or worse) but trust me, it'll be worth it because one day - I promise - I'll build some of the same design features into a bass!
 

Doesn't matter what you're making.

I'd follow the thread if you were building a sideboard.

Edited by Cato
  • Like 4
  • Haha 1
Link to comment
Share on other sites

23 minutes ago, TheGreek said:

I hope this doesn't become a "design by committee" but here's my 2p worth.

As Andy knows I was very pedantic about how the lines flowed in my Psilos. I've made a few amendments to Andy's design which, I believe, help the lines flow. This includes moving the lower cut back 1 fret.

Note how the bottom horn flows more into both the top horn and into the armpit cut which makes it easier on the eye. By adjusting where the top cut is made you can make the eye flow more pleasing (IMO).

What do others think??

5a7f524496656_andysguitar.png.acb228249de20dc05b57cf9740cee96d.png

Some good lines there, Mick :)

I'll be moving the lower waist back towards the tailstock.  I'll repost the pic sometime soon (and explain why I'm moving the waist :) )

Link to comment
Share on other sites

At the same time as I've been getting my head round the project, I've been trying to teach myself how to use Inkscape.   To be honest, I've only just gleaned from forum discussions that such a package exists!

First of all, this is one of the options for the top wood I may be using:
VEfkaEAl.jpg


An this below is my first attempt at clipping a photo of the amboyna with the shape designed on the package and overlain with the 25" scale-length component templates taken from a photo of my own Swift Lite prototype. Where I've been able to get the package to cooperate, I've incorporated a couple of Mick @TheGreek 's suggestions and also moved the lower waist back a touch.  At this stage it's feasibility stuff so will need refining in any case.

To a lot of you CAD afficianados I know this is kids stuff, but I'm well, well chuffed with the package and the results  :D      :
 

DZcKLNRh.jpg%20 

Link to comment
Share on other sites

8 minutes ago, Jimothey said:

I’ve just started using Inkscape aswell that’s what I used to design my scratch build except I can’t seem to get the photo crop then applying it to the body function to work properly 

But that’s looking really good:D

I cheated a bit - I managed to get the crops (or should I say 'clip's ) working fine, but the above is then more a series of clips pasted on top of each other - I have no doubt there is a better way of doing it :) 

Link to comment
Share on other sites

Amboyna is a beautiful timber - my ACG Harlot is made of this - however over time it's gone from an orange/red to brown. The grain, especially the spalted/bird's eye like you have, is a pleasure on the eye. My nephew used to work at John Lewis where they sold really expensive pens made from slivers.

Looking forward to following this build.

  • Like 1
Link to comment
Share on other sites

IMO (and especially on a guitar) cutaways should give easy access to ALL of the frets.

Also I was meaning to ask on your last guitar build, when you essentially removed the heal and blended the neck into the body how does that affect the action of the truss rod? My understanding was that the truss rod acted on the neck between the nut/volute and where the neck thickens at the heal. If you remove the heal essentially making the neck longer do you need a longer truss rod?

Link to comment
Share on other sites

1 minute ago, BigRedX said:

Also I was meaning to ask on your last guitar build, when you essentially removed the heal and blended the neck into the body how does that affect the action of the truss rod? My understanding was that the truss rod acted on the neck between the nut/volute and where the neck thickens at the heal. If you remove the heal essentially making the neck longer do you need a longer truss rod?

No - the truss rod is in its normal position.  If you think about it, mine is no different to a bolt-on neck, but with no extra depth of the body underneath the bolt-on neck heel.  The bending moment of the truss rod is pushing up in the middle of the fretboard and down either end so if you think of a bolt-on neck, unless the truss rod ends push their way through the slot floor, the neck will bend, whether it is bolted on or not.  With neck-throughs, I think you can get issues if the body end of the rod extends too far, because the rod itself is trying to bend but the length that is held rigid by the body will not move at all.

It took me a while to work out how this all interacted together, greatly aided by Tom's African build, if you remember that most unlikely of scenarios, where Tom's was basically a neck doing ALL of the functional stuff and the body just somewhere to fix one of the strap buttons onto xD

  QpOPJjDl.jpg

Q5Gi4Ikl.jpg

...and that's still going strong I understand :)

Link to comment
Share on other sites

2 hours ago, Andyjr1515 said:

No - the truss rod is in its normal position.  If you think about it, mine is no different to a bolt-on neck, but with no extra depth of the body underneath the bolt-on neck heel.  The bending moment of the truss rod is pushing up in the middle of the fretboard and down either end so if you think of a bolt-on neck, unless the truss rod ends push their way through the slot floor, the neck will bend, whether it is bolted on or not.  With neck-throughs, I think you can get issues if the body end of the rod extends too far, because the rod itself is trying to bend but the length that is held rigid by the body will not move at all.

It took me a while to work out how this all interacted together, greatly aided by Tom's African build, if you remember that most unlikely of scenarios, where Tom's was basically a neck doing ALL of the functional stuff and the body just somewhere to fix one of the strap buttons onto xD

  QpOPJjDl.jpg

Q5Gi4Ikl.jpg

...and that's still going strong I understand :)

I just looked at this thread for this build awesome!!!!!

  • Like 1
Link to comment
Share on other sites

I got round to having a look at the oak shelf and cut it into body-sized lengths:

OzbBy6Fl.jpg

It's a bit cupped, so I ran it through the thicknesser first to take the hump off, and then reversed to take the wings off.  Once it was flat and straight, I thicknessed it down to the nominal 25mm starting point:

r86I6Ipl.jpg

 

It will be cut into two wings, either side of the neck and is presently around 30mm wider than needed - as such, I will take off the excess from the rhs in this shot, bringing the feature figuring pretty much into the middle.  While the neck will break that feature up - and the back will be scooped -  hopefully there will still be a continuity of figuring showing either side of the neck. 

For oak, it doesn't feel too heavy.  When I cut the excess off, I'll thickness a length of the offcut and compare the weight with a similar blank of the sapele.

The other good news is - do you remember I made a wrong cut on Tim's Alembicesque and had to re-make the neck (below is the remade one)?

UuUqZGQl.jpg

 

Well - I've still got the original neck.  It's here:

DbXhJ1yl.jpg

 

It only couldn't be used because I'd already cut the top for Tim's.  And I haven't cut the top yet for Jane's :D.   So I can use it!  It even has the correct neck angle, etc, etc, already done :biggrin: 

 

Edited by Andyjr1515
Link to comment
Share on other sites

Soon time to draw the first blood and start cutting wood. 

I've sorted the join line of the amboyna and tweaked the shape a little - actually, this will probably be tweaked 0.5cm wider either side of the centre line and bring the upper waist down a bit steeper round the lower bout, but this is the kind of shape:
GBijA88l.jpg

This evening I will glue the two halves together and tomorrow, cut out the shape.

Some of you will know that I use the fancy top as the routing template - absolutely not recommended by most builders so I don't encourage you to do likewise.

Link to comment
Share on other sites

14 hours ago, Andyjr1515 said:

Soon time to draw the first blood and start cutting wood. 

I've sorted the join line of the amboyna and tweaked the shape a little - actually, this will probably be tweaked 0.5cm wider either side of the centre line and bring the upper waist down a bit steeper round the lower bout, but this is the kind of shape:
GBijA88l.jpg

This evening I will glue the two halves together and tomorrow, cut out the shape.

Some of you will know that I use the fancy top as the routing template - absolutely not recommended by most builders so I don't encourage you to do likewise.

...and others are waiting for the day that you give your router flying lessons after it delivers a vicious bite to your book-matched bits.

Heeheehee.

I hope I have not tempted fate with my facetious comment.

Link to comment
Share on other sites

5 hours ago, SpondonBassed said:

...and others are waiting for the day that you give your router flying lessons after it delivers a vicious bite to your book-matched bits.

Heeheehee.

I hope I have not tempted fate with my facetious comment.

I'm sure not :D 

I think with my builds, fate has ample opportunity to do its worst whatever xD

  • Haha 1
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Recently Browsing   0 members

    • No registered users viewing this page.
×
×
  • Create New...