Aero71 Posted November 26, 2017 Share Posted November 26, 2017 (edited) For sale:Genuine 1971 Fender Precision neck with fretless rosewood fretboard.The neck is in great condition, used but very neat.Truss rod works in both ways.Nut width is 41.3 mm,Neck stamp says; 5 02 71Comes including the original tuners and string tree. I believe this neck was fretted original, the side dots are in the right position, so it should be easy for a luthier to install frets again. £525 Can be shipped save and secure for £20 sold Edited December 11, 2017 by Aero71 Link to comment Share on other sites More sharing options...
floFC Posted November 26, 2017 Share Posted November 26, 2017 Why do you think it was originally fretted? I couldn’t see any lines where the frets would have been removed from. Any close ups? Link to comment Share on other sites More sharing options...
Beedster Posted November 26, 2017 Share Posted November 26, 2017 Early 70s FL boards were plain, no lines or dots. Might be a rare exception, but most likely it was originally fretted. C 1 Link to comment Share on other sites More sharing options...
floFC Posted November 26, 2017 Share Posted November 26, 2017 I see, thanks. I really can't see any traces of frets. In any case, the fretboard is beautiful. Link to comment Share on other sites More sharing options...
Beedster Posted November 26, 2017 Share Posted November 26, 2017 I imagine it's a replacement fretboard as opposed to a very good de-fret. As I said, it could just possibly be original, a custom order perhaps, but if so I've never seen one like it. Link to comment Share on other sites More sharing options...
Aero71 Posted November 26, 2017 Author Share Posted November 26, 2017 There are no lines or marks from previous frets, so I think the fretboard was replaced. Link to comment Share on other sites More sharing options...
Dan Dare Posted November 27, 2017 Share Posted November 27, 2017 Looking at the thinness of the fretboard in the end-on photo, I'd say it's likely the board was planed when the frets were pulled to remove the slots. They are normally thicker than that. Link to comment Share on other sites More sharing options...
Beedster Posted November 27, 2017 Share Posted November 27, 2017 Think it's just been shaved a few times to be honest, occupation hazard with a rosewood board, I suspect you'd still see where the frets were if it had been shaved to remove the fret slots. Link to comment Share on other sites More sharing options...
wateroftyne Posted November 27, 2017 Share Posted November 27, 2017 Where are the side dots? On the note = fretless Betwen the notes = fretted Link to comment Share on other sites More sharing options...
Beedster Posted November 27, 2017 Share Posted November 27, 2017 My factory US precision fretless has side dots between the notes, bloody annoying to be honest, and there's a thread about it on somewhere. I think the upshot of that thread was that they make the necks, dots and all, and then a few of them are destined to be f/less. No idea if that was the case in '71 though, more your area of expertise WoT? Link to comment Share on other sites More sharing options...
franzbassist Posted November 27, 2017 Share Posted November 27, 2017 Early 70s factory fretless Ps were definitely dots on the line and not mid "fret". Link to comment Share on other sites More sharing options...
Aero71 Posted November 27, 2017 Author Share Posted November 27, 2017 These are mid fret dots, both fretboard dots and side dots, so there would be no problem if you decide to get it fretted again. Link to comment Share on other sites More sharing options...
Dan Dare Posted November 27, 2017 Share Posted November 27, 2017 May struggle to re-fret that board because it's so thin. They'd likely bite into the neck material itself Link to comment Share on other sites More sharing options...
Tonteee Posted November 27, 2017 Share Posted November 27, 2017 (edited) I would worry the same, sadly. Radius looks a bit odd to me, too. I wonder if you can re-board a neck. Something I'm sure one of BC's ultra clever luthierie would know - just not something I'd thought about previously. Or maybe just enjoy a fretless 1971 P neck! Lovely grain on that Rosewood. Edited November 27, 2017 by Tonteee Link to comment Share on other sites More sharing options...
franzbassist Posted November 27, 2017 Share Posted November 27, 2017 You can definitely re-board it. I had Brook Guitars in Devon convert a maple boarded P to an ebony unlined fretless and they did an amazing job - even kept the original nut! 1 Link to comment Share on other sites More sharing options...
wateroftyne Posted November 27, 2017 Share Posted November 27, 2017 Ooof... I do like a nice slab of ebony. Link to comment Share on other sites More sharing options...
Tonteee Posted November 27, 2017 Share Posted November 27, 2017 Thanks for the clarify, WB. Link to comment Share on other sites More sharing options...
Aero71 Posted November 29, 2017 Author Share Posted November 29, 2017 Indeed it can be re-boarded or just leave it like this and enjoy fretless. Link to comment Share on other sites More sharing options...
Aero71 Posted December 8, 2017 Author Share Posted December 8, 2017 Pricedrop £450 delivered Link to comment Share on other sites More sharing options...
Aero71 Posted December 11, 2017 Author Share Posted December 11, 2017 sold on the bay Link to comment Share on other sites More sharing options...
.gif.9ad672bb8b84505709f76b39c8c256ec.gif)
Recommended Posts