All Activity

A set of the above, including fixing screws, compatible with Mexican Fenders. Price includes postage in UK.

A useful single channel line level isolating transformer for removing hum loops from PA, Mixer etc in a very solid metal case Input on either XLR or 6.3mm Jack - balanced or unbalanced Balanced output on XLR or 6.3mm Jack Switches for ground lift and phase reverse. The third switch provides either unity 1:1 or a 2:1 ratio tap for long cable runs There is a small circuit diagram on the top to remind you what all the connectors and switches do! Quoted frequency range is 20Hz to 25kHz at line level Dimensions 120 x 44 x 90 mm

Excellent solid and versatile active DI box from Canford Audio, only selling since I have three of these It comes with the instruction leaflet Inputs for Instrument or Amp output. Output jack for Amp input or speaker cab alongside. Balanced XLR output to mixer on the reverse. Instrument input 1.8M ohm impedance - so no loading of amp input or pickups Phantom powered off the mixer XLR or by 9v battery

Fender Precision bass in Tidepool from 2020. The bass has a satin urethane finish on the neck and is in near mint condition. Takes a great set up and only has a tiny mark on the P in Precision Bass on the headstock which is barely noticeable and can’t be seen in the close up photo as it is that small. Weight is 4kg. Price is £550 but I am open to sensible offers. Local pickup only from the Coalisland area. Feel free to ask any questions.

This box has a set of three Speakon connectors wired in parallel (using pins 1 & 2) so can be used as an extender for speaker cables, or to allow two cabs to be driven from the same amp One connector at one end and two at the other end The box is made from very solid extruded aluminium

I bought this very well upholstered Gator gig bag (current retail £135) for my Guild Starfire bass, but although it fits, its a bit tighter lengthwise than seems sensible, so this has barely been used. It is fairly obviously sized for a Gibson 335 guitar, but will also fit a flying V or a short-scale bass that's a fraction smaller than a Starfire Loads of padding, loads of pockets and a waterproof cover (in pocket 6 on the back, I think - depends how you count the pockets) The padding at the base of the bag can be removed (its on velcro) to give a couple of cm extra space - the quoted overall internal length is without this extra padding fitted Pickup preferred, but I will post it, although I haven't worked out what that would cost, let me know if you're interested and I'll get a price. Internal size: Overall Length: 46.1" (117.09 cm) Body Length: 25.0" (63.5 cm) Body Height: 3.5" (8.89 cm) Lower Bout Width: 17.3" (43.94 cm) Middle Bout Width: 15.4" (39.12 cm) Upper Bout Width: 13.0" (33.02 cm) Exterior Dimensions: Length: 47.8" (121.41 cm) Width: 18.3" (46.48 cm) Height: 6.9" (17.53 cm)

LA Audio high quality active DI box, very solid construction; comes with an instruction leaflet - which is worth reading since the box is deceptively versatile! This works off an 18v rail so can cope with high or low level signals. Power via phantom from your mixer or 2 x 9v batteries Usefully it has a +20db switch to increase the level of low output devices and with 1M ohm input impedance is compatible with piezo pickups The Input will work with Instrument or Speaker levels ('Pad' switch is for speaker level), isolated XLR output for your mixer and a 'link' output to take the signal on to an amp or cab A separate unbalanced output is available as well as the balanced XLR

Anyone need a PA amp? Usual excellent Crown quality, this amp has only had light use and comes in a Chord carry bag. Not sure what the total weight is, but the amp on its own is under 4kg, so very portable XLR inputs, Speakon outputs for most users, plus various other options as per photos As well as standard Stereo, the amp can be configured as follows: Crossover Mode (CH1=LPF, CH2=HPF) – this mode enables a LowPass Filter on Channel 1 and a HighPass Filter on Channel 2 at the frequency chosen. LowPass Mode (CH1=LPF, CH2=LPF) – this mode enables a LowPass Filter on both Channel 1 and Channel 1 at the frequency chosen. HighPass Mode (CH1=HPF, CH2=HPF) – this mode enables a HighPass Filter on both Channel 1 and Channel 2 at the frequency chosen. You can also put it into 'Bridge' mode for seriously high levels of output (according to the spec 1.5kW into 4ohm) Pickup from Uxbridge area, or I'll courier to you at cost.